ExtremeSwitching (EXOS)

Expand all | Collapse all

problem with Config Booted on summit x450-g4

  • 1.  problem with Config Booted on summit x450-g4

    Posted 01-13-2017 19:41
    when i configured switch this save configuration but if the switch reboot lost the configuration, i can see this configuration in the switch:

    information on SW
    ####################
    Slot: Slot-1 * Slot-2 ------------------------ ------------------------
    Current State: MASTER BACKUP (In Sync)

    Image Selected: secondary secondary
    Image Booted: secondary secondary
    Primary ver: 16.1.0.18 16.1.0.18
    Secondary ver: 22.1.1.5 22.1.1.5

    Config Selected: primary.cfg
    Config Booted: Factory Default

    primary.cfg Created by ExtremeXOS version 22.1.1.5
    577404 bytes saved on Fri Jan 13 20:33:50 2017



  • 2.  RE: problem with Config Booted on summit x450-g4

    Posted 01-13-2017 19:47
    Hello Salvador,

    You checked the "show config" to see if the config is missing? This is a stack, did you reboot the entire stack?


  • 3.  RE: problem with Config Booted on summit x450-g4

    Posted 01-13-2017 20:15
    yes, i reboot the stack and the config lost, yesterday config this in the sw:

    BootRom > config noneBootRom > boot after this config the switch lost the config the switch up with factory default [/code]


  • 4.  RE: problem with Config Booted on summit x450-g4

    Posted 01-13-2017 20:32
    Is there a reason you went to the bootrom and config none?


  • 5.  RE: problem with Config Booted on summit x450-g4

    Posted 01-13-2017 20:32
    and how i can solve this problem ?



  • 6.  RE: problem with Config Booted on summit x450-g4

    Posted 01-13-2017 20:32
    Can you explain to me why the bootrom was accessed? Was this after it didn't boot into the config or before?


  • 7.  RE: problem with Config Booted on summit x450-g4

    Posted 01-13-2017 20:32
    i need to restore to factory and in enterasys this was the procedure and i suppose that the process was the same


  • 8.  RE: problem with Config Booted on summit x450-g4

    Posted 01-13-2017 20:32
    Hello Salvador,

    Can you explain the order of events? Config, Bootrom, Reboot?

    unconfigure switch all will factory restore the configuration in exos. This is assuming you can login.


  • 9.  RE: problem with Config Booted on summit x450-g4

    Posted 01-13-2017 20:32
    is all



  • 10.  RE: problem with Config Booted on summit x450-g4

    Posted 01-13-2017 20:32
    In what order?


  • 11.  RE: problem with Config Booted on summit x450-g4

    Posted 01-13-2017 20:32
    ok, in this case reboot the switch and them press space bar and put de command config none and reboot, after when i configure save configuration and reboot the switch lost the configuration


  • 12.  RE: problem with Config Booted on summit x450-g4

    Posted 01-15-2017 00:14
    Please emphasize on the order in which it was accessed......We knew t hat you had factory defaulted the switch to unconfigure all.


  • 13.  RE: problem with Config Booted on summit x450-g4

    Posted 01-16-2017 04:51
    HI Salvador,

    As per the output of show switch, the switch is booted with the "factory default" configuration.
    If we reset the switch with the command below,

    BootRom > config none

    This is an expected behaviour that the switch will boot with the factory default configuration after the command above in the bootrom.

    Config Selected: primary.cfg

    We might have a problem if you jus reboot the stack now and if it not loaded with the primary.cfg as mentioned above. So, please clarify the issue so that we can help you further.

    Thanks.



  • 14.  RE: problem with Config Booted on summit x450-g4

    Posted 03-10-2021 07:36

    hello Salvador 

     

    Did you solve the issue?