ExtremeSwitching (EXOS)

Expand all | Collapse all

How to setup sharing in MLAG for Windows Server NIC Teaming ?

  • 1.  How to setup sharing in MLAG for Windows Server NIC Teaming ?

    Posted 03-08-2018 15:08
    Hello,

    What is the best sharing algorithm for connecting Windows Server 2012 NIC teaming ?
    We have a MLAG disign at the core and NIC teaming mode on Windows is switch independent.

    I guess LACP is not good choice here (?).

    REGARDS


  • 2.  RE: How to setup sharing in MLAG for Windows Server NIC Teaming ?

    Posted 03-14-2018 13:28
    So, I was trying to use all address-based algorithms (L2/L3/L3_L4) with and without LACP.
    With no success, unfortunately.

    Here is my CORE1 mlag peer config (not full, of course):

    configure snmp sysName "CORE1"
    configure snmp sysLocation "some location"
    configure snmp sysContact "some contact"
    configure slot 1 module X670G2-48x-4q
    configure sys-recovery-level slot 1 reset
    configure slot 2 module X460G2-48t-10G4
    configure sys-recovery-level slot 2 reset
    create vlan "isc"
    configure vlan isc tag 1001
    enable sharing 1:13 grouping 1:13 algorithm address-based L3_L4 lacp
    configure vlan isc ipaddress 192.168.101.1 255.255.255.0
    create mlag peer "isc_core"
    configure mlag peer "isc_core" ipaddress 192.168.101.2 vr VR-Default
    enable mlag port 1:13 peer "isc_core" id 13[/code]
    and CORE2 mlag peer config:

    configure snmp sysName "CORE2"
    configure snmp sysLocation "some location"
    configure snmp sysContact "some contact"
    configure slot 1 module X670G2-48x-4q
    configure sys-recovery-level slot 1 reset
    configure slot 2 module X460G2-48t-10G4
    configure sys-recovery-level slot 2 reset

    create vlan "isc"
    configure vlan isc tag 1001
    enable sharing 1:13 grouping 1:13 algorithm address-based L3_L4 lacp
    configure vlan isc ipaddress 192.168.101.2 255.255.255.0

    create mlag peer "isc_core"
    configure mlag peer "isc_core" ipaddress 192.168.101.1 vr VR-Default
    enable mlag port 1:13 peer "isc_core" id 13[/code]

    Whenever I changed to "lacp" on sharing, I changed respectively the NIC setting on server side to "lacp" as well. But it gave nothing...

    When I change to sharing within single core (not through MLAG, all NIC-Team adapters on the same core), the lag started working (?).
    I have expected the lag to run over MLAG as if it was on single core.

    Anyone have successfully connected Windows Server 2012 NIC-Team through MLAG ?

    Regards
    Robert



  • 3.  RE: How to setup sharing in MLAG for Windows Server NIC Teaming ?

    Posted 03-14-2018 13:28
    Is mlag peer isc_core the correct name used for both? I believe they should be different.
    Edit: just checked a config. Looks like they can be the same.

    something comes to mind about single port share. Have you tried setting up a single port share on each mlag peer for on the port the server is connected to?


  • 4.  RE: How to setup sharing in MLAG for Windows Server NIC Teaming ?

    Posted 03-14-2018 13:28
    Found an article that alludes to the single port share: https://gtacknowledge.extremenetworks.com/articles/How_To/How-to-configure-MLAG-in-Extreme-switches

    Towards the bottom: Please also note if the downstream device (e.g. switch, server, etc..) is using LACP LAG sharing on its ports, it will be necessary to enable LACP LAG on the MLAG ports. This has to be done prior to enabling the port for mlag


  • 5.  RE: How to setup sharing in MLAG for Windows Server NIC Teaming ?

    Posted 03-14-2018 13:28
    Hello Brian !

    Each time I was changing the sharing lacp options, I disabled the mlag on both peers, then disabled sharing, enabled sharing with new options and enabled mlag again.


  • 6.  RE: How to setup sharing in MLAG for Windows Server NIC Teaming ?

    Posted 03-14-2018 13:28
    Sorry, just re-read your original post and you mentioned that. Just didn't see it in the config. Just checking, is your server vlan tagged on the ISC links?


  • 7.  RE: How to setup sharing in MLAG for Windows Server NIC Teaming ?

    Posted 03-14-2018 13:28
    Sure, I have all my user and server vlans tagged on the ISC link (which is 2 x 10Gb sharing port).
    One thing I forgot to mention: when I check the MLAG status at EMC maps, all working MLAGS are shown as "up", but the one for server is "protecting" (don't know exactly what does it mean: have read EXOS 22.x user guide, but found no word about MLAG possible states).