ExtremeSwitching (EXOS)

Expand all | Collapse all

Initial Configuration BD8810

Mario Cruz Torres

Mario Cruz Torres09-25-2017 19:46

  • 1.  Initial Configuration BD8810

    Posted 09-24-2017 12:03
    Hello Expert,

    Im start configuring my first BD8810:

    First I want to upgrade the node, but for that I configure a vlan with an IP Address but Im unable to ping the IP. [My computer has the 192.168.1.2/24]

    This is my config:

    enable port 1:1
    create vlan "test"
    configure vlan test tag 10
    configure vlan test add ports 1:1 untagged
    configure vlan test ipaddress 192.168.1.1 255.255.255.0
    enable ipforwarding vlan test

    There is something that I missing?? Maybe something new for the BlackDiamonds

    Thanks


  • 2.  RE: Initial Configuration BD8810

    Posted 09-24-2017 12:11
    Hi Mario Cruz,

    I see all the necessary configuration for the communication to happen between the PC (192.168.1.24/24) and the BD8810 (192.168.1.1/24).
    I don't see a reason as to why the ping will not go through between the switch and the PC.

    Is there any firewall that is enabled in the PC that could be taken down and checked?

    What about the port LED status and please check the output of "show port 1:1" to see if the status of the port is "Enabled" and "Active".

    Thank You,
    Muthuraman


  • 3.  RE: Initial Configuration BD8810

    Posted 09-24-2017 12:20
    Hi Mario Cruz,

    Is ping from both the direction not functional or is the ping in any 1 direction not functional.

    Also, please check the output of "show fdb port 1:1" to see if the MAC of the PC is learnt in the switch. And also check the output of "show iparp" to see if the IP address of the PC is learnt in the switch.

    Let us also check if there are any errors occurring in the port and the command is as below,

    - show port 1:1 rxerror
    - show port 1:1 txerror

    Thank You,
    Muthuraman


  • 4.  RE: Initial Configuration BD8810

    Posted 09-24-2017 13:33
    Hi Mario Cruz,

    The port seems to have the right configuration and the broadcast is enabled in the switch.

    Please run wireshark in the PC and initiate a ping to the switch IP address and see if there are any ARP reply received from the switch.

    Thank You,
    Muthuraman


  • 5.  RE: Initial Configuration BD8810

    Posted 09-24-2017 14:02
    Can we see a "show vlan" output, "show port 1:1 vlan" (should be there in 16.1) and a "show vlan 100" (as it seems the port is in vlan 100, not 10)?


  • 6.  RE: Initial Configuration BD8810

    Posted 09-24-2017 16:53
    Another way to confirm is

    show fdb port 1:1 .....

    fdb entry will show what vlan the switch is learning the mac address on... does sound like you may have created another vlan with tag id 100 that is untagged on port 1:1 so when you tried to add test untagged it should have returned a warning that there was already an untagged vlan on that port.

    Show ipr vr vr-def would also confirm what vlan and tag the ip is on



  • 7.  RE: Initial Configuration BD8810

    Posted 09-24-2017 12:32
    Hi Mario Cruz,

    Please share the complete output of "show port 1:1 information detail" and "show switch" from the BD8810.

    Thank you,
    Muthuraman


  • 8.  RE: Initial Configuration BD8810

    Posted 09-25-2017 03:50
    I think this issue will be if you new to Extreme the you are not using "VR-Default" and by default you are pinging from the MGMT

    try this

    ping vr "VR-Default" 192.168.1.2

    let me know if that works



  • 9.  RE: Initial Configuration BD8810

    Posted 09-25-2017 04:03
    please note there was a typo in my original response I have corrected but it should have read

    ping vr "VR-Default" 192.168.1.2



  • 10.  RE: Initial Configuration BD8810

    Posted 09-25-2017 19:46
    Maybe is need it a License??


  • 11.  RE: Initial Configuration BD8810

    Posted 09-25-2017 20:00
    what does show iparp say? If you have an arp entry for the 10.0.0.2 in the test vlan with the mac of your laptop then your laptop still has a firewall enabled and is block icmp.

    Your configuration looks good


  • 12.  RE: Initial Configuration BD8810

    Posted 09-25-2017 20:03
    Hi Mario,

    Your config looks OK to me. I still suspect an issue with the FW on your computer. Can you try to totally disable it again, restart the PC and retest. Please let us know the outcome after performing those steps. Thank you.

    Best regards,
    Andrew


  • 13.  RE: Initial Configuration BD8810

    Posted 09-25-2017 20:10
    Hello,

    I think we solve the issue we removed the MSM Master and change it. After this the ping was ok..

    Do you think that this card is faulty?

    Thanks everyone

    Mario Cruz



  • 14.  RE: Initial Configuration BD8810



  • 15.  RE: Initial Configuration BD8810

    Posted 10-01-2017 22:32
    Hi,
    There is the article for ”Diagnostics” EXOS.

    How to Diagnose-hardware failures using EXOS
    https://gtacknowledge.extremenetworks.com/articles/How_To/How-to-Diagnose-hardware-failures-using-EX...

    Best regards,


  • 16.  RE: Initial Configuration BD8810

    Posted 09-24-2017 12:11
    Hello Muthuraman,

    I remove the firewall on my laptop and the same issue.
    The port is Active no issue with the cable.

    There is something new for the BD to configure?? Like the modules? We just power on the equipments.

    Thanks for the quick response.


  • 17.  RE: Initial Configuration BD8810

    Posted 09-24-2017 12:20
    Hi,

    Ping is not functional in both directions.

    The MAC is learned via the fdb command but no via the iparp, And looking for the errors there is no such on the port.

    Any idea.

    Thanks

    Mario


  • 18.  RE: Initial Configuration BD8810

    Posted 09-24-2017 12:32
    Follow the info:
    * BD-8810.165 # sh ports 1:1 information detail
    Port: 1:1
    Virtual-router: VR-Default
    Type: UTP
    Random Early drop: Unsupported
    Admin state: Enabled with auto-speed sensing auto-duplex
    Link State: Active, 1Gbps, full-duplex
    Link Ups: 11 Last: Sun Sep 24 14:38:17 2017
    Link Downs: 10 Last: Sun Sep 24 14:33:56 2017

    VLAN cfg:
    Name: test, Internal Tag = 100, MAC-limit = No-limit, Virtual router: VR-Default
    STP cfg:

    Protocol:
    Name: test Protocol: ANY Match all protocols.
    Trunking: Load sharing is not enabled.

    EDP: Enabled

    ELSM: Disabled
    Ethernet OAM: Disabled
    Learning: Enabled
    Unicast Flooding: Enabled
    Multicast Flooding: Enabled
    Broadcast Flooding: Enabled
    Jumbo: Disabled
    Flow Control: Rx-Pause: Enabled Tx-Pause: Disabled
    Priority Flow Control: Disabled
    Reflective Relay: Disabled
    Link up/down SNMP trap filter setting: Enabled
    Egress Port Rate: No-limit
    Broadcast Rate: No-limit
    Multicast Rate: No-limit
    Unknown Dest Mac Rate: No-limit
    QoS Profile: None configured
    Ingress Rate Shaping : Unsupported
    Ingress IPTOS Examination: Disabled
    Ingress 802.1p Examination: Enabled
    Ingress 802.1p Inner Exam: Disabled
    Ingress 802.1p Priority: 0
    Egress IPTOS Replacement: Disabled
    Egress 802.1p Replacement: Disabled
    NetLogin: Disabled
    NetLogin port mode: Port based VLANs
    Smart redundancy: Enabled
    Software redundant port: Disabled
    IPFIX: Disabled Metering: Ingress, All Packets, All Traffic
    IPv4 Flow Key Mask: SIP: 255.255.255.255 DIP: 255.255.255.255
    IPv6 Flow Key Mask: SIP: ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff
    DIP: ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff

    auto-polarity: Enabled
    Shared packet buffer: default
    VMAN CEP egress filtering: Disabled
    Isolation: Off
    PTP Configured: Disabled
    Time-Stamping Mode: None

    Dynamic VLAN Uplink: Disabled
    VM Tracking Dynamic VLANs: Disabled

    ------------------------------------------------------------------
    * BD-8810.166 # show switch

    SysName: BD-8810
    SysLocation:
    SysContact: support@extremenetworks.com, +1 888 257 3000
    System MAC: 00:04:96:9C:C0:60
    System Type: BD-8810

    SysHealth check: Enabled (Normal)
    Recovery Mode: All
    System Watchdog: Enabled

    Current Time: Sun Sep 24 14:39:11 2017
    Timezone: [Auto DST Disabled] GMT Offset: 0 minutes, name is UTC.
    Boot Time: Thu Sep 21 15:24:17 2017
    Boot Count: 3
    Next Reboot: None scheduled
    System UpTime: 2 days 23 hours 14 minutes 54 seconds

    Slot: MSM-A * MSM-B
    ------------------------ ------------------------
    Current State: MASTER BACKUP (In Sync)

    Image Selected: primary primary
    Image Booted: primary primary
    Primary ver: 16.1.3.6 16.1.3.6
    Secondary ver: 16.1.3.6 16.1.3.6

    Config Selected: NONE NONE
    Config Booted: Factory Default Factory Default

    --------------------------------------------------------------------------------

    Thanks so much for this help

    Mario Cruz



  • 19.  RE: Initial Configuration BD8810

    Posted 09-24-2017 16:53
    Hello I verify,

    I changed to another config:

    #
    # Module devmgr configuration.
    #
    configure snmp sysContact "support@extremenetworks.com, +1 888 257 3000"
    configure slot 1 module G48Tc
    configure sys-recovery-level slot 1 reset
    configure slot 2 module G48Tc
    configure sys-recovery-level slot 2 reset
    configure slot 10 module 8900-10G8X-xl
    configure sys-recovery-level slot 10 reset

    #
    # Module vlan configuration.
    #
    configure vlan default delete ports all
    configure vr VR-Default delete ports 1:1-48,2:1-48,10:1-8
    configure vr VR-Default add ports 1:1-48,2:1-48,10:1-8
    configure vlan default delete ports 1:3-4
    create vlan "test"
    configure vlan test tag 300
    configure vlan Default add ports 1:1-2,1:5-48,2:1-48,10:1-8 untagged
    configure vlan test add ports 1:3-4 untagged
    configure vlan test ipaddress 10.0.0.1 255.255.255.252
    enable ipforwarding vlan test

    -------------------------------------------------------------------

    * BD-8810.69 # sh fdb
    Mac Vlan Age Flags Port / Virtual Port List
    --------------------------------------------------------------------------------
    d0??9c:22:17:23 test(0300) 0044 d m 1:3

    Flags : d - Dynamic, s - Static, p - Permanent, n - NetLogin, m - MAC, i - IP,
    x - IPX, l - lockdown MAC, L - lockdown-timeout MAC, M- Mirror, B - Egress Blackhole,
    b - Ingress Blackhole, v - MAC-Based VLAN, P - Private VLAN, T - VLAN translation,
    D - drop packet, h - Hardware Aging, o - IEEE 802.1ah Backbone MAC,
    S - Software Controlled Deletion, r - MSRP,
    R - TRILL Rbridge, Z - OpenFlow

    Total: 1 Static: 0 Perm: 0 Dyn: 1 Dropped: 0 Locked: 0 Locked with Timeout: 0
    FDB Aging time: 300

    ---------------------------------------------------------------------------------

    * BD-8810.70 # show ipr vr "VR-Default"
    Ori Destination Gateway Mtr Flags VLAN Duration
    #d 10.0.0.0/30 10.0.0.1 1 U------um--f- test 0d:0h:31m:5s

    (mo) MOSPF (o) OSPF, (o1) OSPFExt1, (o2) OSPFExt2,
    (oa) OSPFIntra, (oe) OSPFAsExt, (or) OSPFInter, (pd) PIM-DM, (ps) PIM-SM,
    (r) RIP, (ra) RtAdvrt, (s) Static, (sv) SLB_VIP, (un) UnKnown,
    (*) Preferred unicast route (@) Preferred multicast route,
    (#) Preferred unicast and multicast route.

    Flags: (b) BFD protection requested, (B) BlackHole, (c) Compressed, (D) Dynamic,
    (f) Provided to FIB, (G) Gateway, (H) Host Route, (l) Calculated LDP LSP,
    (L) Matching LDP LSP, (m) Multicast, (p) BFD protection active, (P) LPM-routing,
    (R) Modified, (s) Static LSP, (S) Static, (t) Calculated RSVP-TE LSP,
    (T) Matching RSVP-TE LSP, (u) Unicast, (U) Up, (3) L3VPN Route.

    MPLS Label: (S) Bottom of Label Stack
    Mask distribution:
    1 routes at length 30

    Route Origin distribution:
    1 routes from Direct

    Total number of routes = 1
    Total number of compressed routes = 0

    Everything looks fine but ping is not OK

    ----------------------------------------------------------------

    * BD-8810.52 # ping vr "VR-Default" 10.0.0.2
    Ping(ICMP) 10.0.0.2: 4 packets, 8 data bytes, interval 1 second(s).

    --- 10.0.0.2 ping statistics ---
    4 packets transmitted, 0 packets received, 100% loss
    round-trip min/avg/max = 0/0/0 ms

    -------------------------------------------------------------------------

    I verify that the 10.0.0.1 ping [The IP on the switch] is ok.

    * BD-8810.76 # ping vr "VR-Default" 10.0.0.1
    Ping(ICMP) 10.0.0.1: 4 packets, 8 data bytes, interval 1 second(s).
    16 bytes from 10.0.0.1: icmp_seq=0 ttl=64 time=0.433 ms
    16 bytes from 10.0.0.1: icmp_seq=1 ttl=64 time=0.161 ms
    16 bytes from 10.0.0.1: icmp_seq=2 ttl=64 time=0.164 ms
    16 bytes from 10.0.0.1: icmp_seq=3 ttl=64 time=0.154 ms

    --- 10.0.0.1 ping statistics ---
    4 packets transmitted, 4 packets received, 0% loss
    round-trip min/avg/max = 0/0/0 ms
    * BD-8810.77 #

    Something maybe wrong with the Switch?

    Thanks



  • 20.  RE: Initial Configuration BD8810

    Posted 09-25-2017 04:03
    I change the config [above]

    Trying to ping correctly not working

    * BD-8810.52 # ping vr "VR-Default" 10.0.0.2
    Ping(ICMP) 10.0.0.2: 4 packets, 8 data bytes, interval 1 second(s).

    --- 10.0.0.2 ping statistics ---
    4 packets transmitted, 0 packets received, 100% loss
    round-trip min/avg/max = 0/0/0 ms

    -------------------------------------------------------------------------

    I verify that the 10.0.0.1 ping [The IP on the switch] is ok.

    * BD-8810.76 # ping vr "VR-Default" 10.0.0.1
    Ping(ICMP) 10.0.0.1: 4 packets, 8 data bytes, interval 1 second(s).
    16 bytes from 10.0.0.1: icmp_seq=0 ttl=64 time=0.433 ms
    16 bytes from 10.0.0.1: icmp_seq=1 ttl=64 time=0.161 ms
    16 bytes from 10.0.0.1: icmp_seq=2 ttl=64 time=0.164 ms
    16 bytes from 10.0.0.1: icmp_seq=3 ttl=64 time=0.154 ms

    --- 10.0.0.1 ping statistics ---
    4 packets transmitted, 4 packets received, 0% loss
    round-trip min/avg/max = 0/0/0 ms
    * BD-8810.77 #