ExtremeSwitching (EOS)

  • 1.  XOS command like EOS show ip interface ?

    Posted 09-04-2015 12:25
    Exists in recent XOS firmware a commnd or commands which check the IP Parameters of a L3 Routing interface ?

    Enterasys EOS does this the followin way:
    Extreme B5
    Chassis Firmware Revision: 06.81.05.0003[/code]sw-mg-eg(su)->router
    sw-mg-eg(su)->router>show ip int
    Vlan 2128 is Admin UP
    Vlan 2128 is Oper UP
    Primary IP Address is 172.16.128.186
    Frame Type Ethernet
    MAC-Address 20B3.99EC.7B0B
    Incoming Accesslist is not set
    MTU is 1500 bytes
    ARP Timeout is 14400 seconds
    Direct Broadcast Disabled
    Proxy ARP is Disabled
    sw-mg-eg(su)->[/code]



  • 2.  RE: XOS command like EOS show ip interface ?

    Posted 09-04-2015 12:29
    Matthias,

    The "show vlan" and "show vlan


  • 3.  RE: XOS command like EOS show ip interface ?

    Posted 09-04-2015 12:30
    Hi Matthias,

    I believe 'show ipconfig' should show what you want. The example below is from an MLAG test setup I have in the lab.

    swi2.1 # show ipconfig Use Redirects : Disabled IpOption LSRR : Enabled IpOption SSRR : Enabled IpOption RR : Enabled IpOption TS : Enabled IpOption RA : Enabled Route Sharing : Disabled Route Compression : Enabled Originated Packets : Don't require ipforwarding Max Shared Gateways : Current: 4 Configured: 4 Route Sharing Hash : CRC Lower
    IRDP: Advertisement Address: 255.255.255.255 Maximum Interval: 600 Minimum Interval: 450 Lifetime: 1800 Preference: 0
    Interface IP Address Flags nSIA isc 1.1.1.2 /30 EU----MPuRX--------- 0 v10 10.10.10.2 /24 EUf---MPuRX--------- 0 v11 11.11.11.2 /24 EUf---MPuRX--------- 0 v12 12.12.12.2 /24 EUf---MPuRX--------- 0 v13 13.13.13.2 /24 EUf---MPuRX--------- 0 v14 14.14.14.2 /24 EUf---MPuRX--------- 0 v15 15.15.15.2 /24 EUf---MPuRX--------- 0 v16 16.16.16.2 /24 EUf---MPuRX--------- 0 v17 17.17.17.2 /24 EUf---MPuRX--------- 0 v18 18.18.18.2 /24 EUf---MPuRX--------- 0 v19 19.19.19.2 /24 EUf---MPuRX--------- 0 v2 2.2.2.2 /24 EUf---MPuRX--------- 0 v20 20.20.20.2 /24 EUf---MPuRX--------- 0 v21 21.21.21.2 /24 EUf---MPuRX--------- 0 v22 22.22.22.2 /24 EUf---MPuRX--------- 0 v23 23.23.23.2 /24 EUf---MPuRX--------- 0 v24 24.24.24.2 /24 EUf---MPuRX--------- 0 v25 25.25.25.2 /24 EUf---MPuRX--------- 0 v26 26.26.26.2 /24 EUf---MPuRX--------- 0 v27 27.27.27.2 /24 EUf---MPuRX--------- 0 v28 28.28.28.2 /24 EUf---MPuRX--------- 0 v3 3.3.3.2 /24 EUf---MPuRX--------- 0 v4 4.4.4.2 /24 EUf---MPuRX--------- 0 v5 5.5.5.2 /24 EUf---MPuRX--------- 0 v6 6.6.6.2 /24 EUf---MPuRX--------- 0 v7 7.7.7.2 /24 EUf---MPuRX--------- 0 v8 8.8.8.2 /24 EUf---MPuRX--------- 0 v9 9.9.9.2 /24 EUf---MPuRX--------- 0
    Flags: (A) Address Mask Reply Enabled (B) BOOTP Enabled (b) Broadcast Forwarding Enabled (D) Duplicate address detected on VLAN, (E) Interface Enabled (f) Forwarding Enabled (g) Ignore IP Broadcast Enabled (h) Directed Broadcast Forwarding by Hardware Enabled (I) IRDP Advertisement Enabled, (M) Send Parameter Problem Enabled (m) Multicast forwarding Enabled, (n) Multinetted VLAN (nSIA ) Number of Secondary IP Addresses (P) Send Port Unreachables Enabled, (R) Send Redirects Enabled (r) Unicast Reverse Path Enabled on at least one port of the VLAN (t) Tentative address, (T) Time Stamp Reply Enabled (u) Send Unreachables Enabled, (U) Interface Up (v) VRRP Enabled, (X) Send Time Exceeded Enabled
    [/code]

    -Brandon


  • 4.  RE: XOS command like EOS show ip interface ?

    Posted 09-04-2015 12:37
    Hi Brandon,
    "show ipconfig" is the command which answer mostly my questions.
    Thanks.

    Do you know especially regarding ip proxy-arp - how to disable this on XOS ?

    Regards


  • 5.  RE: XOS command like EOS show ip interface ?

    Posted 09-04-2015 12:37
    There is no need to disable it, as EXOS will not do proxy ARP unless it is explicitly configured.

    It can be set up for either specific addresses or an entire subnet.

    -Brandon