ExtremeWireless (Identifi)

  • 1.  AP3805i don't register with V2110 Controller

    Posted 05-13-2016 03:41
    When trying to register my AP3805i Accesspoint on my remote site that is connected via PPTP Tunnel at my V2110 Controller, I don't succeed. Accesspoints are shown in the AP List, are approved, set the right MTU size (checked with ping), are pingable (both ways), but when i check the TCP Dump of the Controller i see the AP sending ?Discover? and then try to Register 5 times (both WASP Protocol) but there is no answer but another ?Discover? from the Admin interface of the controller.

    My Topology is as follows: admin interface 10.10.89.1 Gateway 10.10.89.2, PPTP Tunnel 10.10.89.2-10.10.89.200, physical 10.10.88.1, 10.10.88.x routed, IPs at the remote site 192,168.15.xxx routed, no masquerading (NAT), B@AP untagged for the wireless setting

    what did i misconfigure that the AP doesn't get online

    help would be really appreciated!
    br
    Peter


  • 2.  RE: AP3805i don't register with V2110 Controller

    Posted 05-13-2016 05:12
    AP registration on the "Admin/Mgmt" interface is not supported.

    You need to register the AP on one of the ESA ports - make sure that you checkmark "AP registration" on the interface.

    -Ron


  • 3.  RE: AP3805i don't register with V2110 Controller

    Posted 05-13-2016 05:18
    Hi - thanks for your reply! I activated AP registration and MGmt traffic on the physical 1 interface - didn't mention that sry. At the AP i set the cs auth ip manually to 10.10.88.1. when i inspect the Discover Paket sent from the controller to the ap the AC IP is also 10.10.88.1 br Peter


  • 4.  RE: AP3805i don't register with V2110 Controller

    Posted 05-13-2016 13:20
    Peter

    Are you still experiencing issues? If so do you have a route that is not via the admin port default gateway that points to the AP's 192.168.15.x ie via esaX?

    -Gareth


  • 5.  RE: AP3805i don't register with V2110 Controller

    Posted 05-13-2016 13:20
    Gareth,

    Finally your solution did it!

    I entered a manual route and now everything working fine - thanks for your help!
    BR
    Peter


  • 6.  RE: AP3805i don't register with V2110 Controller

    Posted 05-13-2016 13:20
    Peter

    That's great, thanks for letting me know your issue is resolved.

    -Gareth



  • 7.  RE: AP3805i don't register with V2110 Controller

    Posted 05-13-2016 14:28
    Could you please do a advanced ping from the controller GUI to the AP IP.

    As per below screenshot put in the target IP = AP IP, checkmark "Use specific source interface", choose the interface that is used to register the APs in the pull down menu.

    Please let us know the results.




  • 8.  RE: AP3805i don't register with V2110 Controller

    Posted 05-13-2016 14:28
    Hi,

    thats the ping statitics i got




  • 9.  RE: AP3805i don't register with V2110 Controller

    Posted 05-16-2016 10:44
    Hello Peter,

    Are you all set with this issue? Did you get this sorted out?


  • 10.  RE: AP3805i don't register with V2110 Controller

    Posted 05-17-2016 06:47
    Hi! - not really any progress so far - going to set up a new admin network address now and check if that changes anything


  • 11.  RE: AP3805i don't register with V2110 Controller

    Posted 05-17-2016 07:02
    All,

    thanks again for help - finally entering a manual route that was not the standard gateway of the admin network solved the issue!

    br
    Peter