ExtremeWireless (Identifi)

Expand all | Collapse all

mobility tunnel

  • 1.  mobility tunnel

    Posted 05-09-2017 22:42
    I have two controllers WC-35 with version 10.31.01.0048, and C4110 with version 09.21.10.0005, and i would like configure mobility tunnel between tow controllers, the controller´s dont have HA, this is possible?


  • 2.  RE: mobility tunnel

    Posted 05-10-2017 04:57
    Yes


  • 3.  RE: mobility tunnel

    Posted 05-10-2017 15:18
    But is necessary create a HA?


  • 4.  RE: mobility tunnel

    Posted 05-10-2017 18:05
    Hello Salvador,

    you don't need HA!

    Regards
    Stephan


  • 5.  RE: mobility tunnel

    Posted 05-10-2017 18:05
    i tryed and the tunnel does not up, i have differents segment of network on interface of register 10.10.1.0/24 and 10.10.3.0/24. is necesary that the inferfaces have the same network segment?


  • 6.  RE: mobility tunnel

    Posted 05-10-2017 18:05
    No, they don't need to be on the same VLAN/subnet.

    Is a route configured on the controller so they could reach each other - you could try a ping from controller#1 to controller#2 to see whether routing works.


  • 7.  RE: mobility tunnel

    Posted 05-10-2017 20:34
    Mybe there is a firewall between your networks?
    Visit the release notes for the necessary ports.



  • 8.  RE: mobility tunnel

    Posted 05-10-2017 20:40
    The two controllers are in the same LAN conect at the core


  • 9.  RE: mobility tunnel

    Posted 05-11-2017 03:11
    Are you using NTP and do you have the same time on both controllers?
    What do you see in the Reports->Mobility->Mobility Tunnel Matrix?
    What do you see in the Logs for Mobility?



  • 10.  RE: mobility tunnel

    Posted 05-11-2017 13:16
    I assume but if not..add the mobility agents statically in the list?


  • 11.  RE: mobility tunnel

    Posted 05-11-2017 16:36
    i cal see this logs:
    manager: Mobility tunnel establishment failed with Peer 10.15.2.254. Please verify peer's reachability
    agent: Mobility tunnels with Peers reset due to membership credentials change on current controller


  • 12.  RE: mobility tunnel

    Posted 05-11-2017 16:52
    I'm sorry but it's hard to help if you don't provide exact information.....

    1) what is the IP of controller#1&2 interface that you'd like to use for mobility and how are the interface topologies are configured = physical or bridge@EWC

    2) could you ping the IP this IP from controller#1 and vice-versa


  • 13.  RE: mobility tunnel

    Posted 05-11-2017 16:52
    this is the information of controllers:

    controller 1: interface physical 10.10.2.254/ 24 with Ap registrering, version 09.21.10.0005
    controller 2: interface physical 10.10.3.254/ 24 with Ap registrering, version 10.31.01.0048

    and ping is successfull in both directions.

    but controller 1 have 61 VNS configured and other controller have 3 VNS.



  • 14.  RE: mobility tunnel

    Posted 05-11-2017 16:52
    That IPs don't match with the IPs in the error message that you've provided...

    "manager: Mobility tunnel establishment failed with Peer 10.15.2.254."


  • 15.  RE: mobility tunnel

    Posted 05-11-2017 16:52
    sorry, the Second octet is 15 for both segment of network, 10.15.2.254/24 and 10.15.3.254/24