IQ Engine/HiveOS Announcements

Expand all | Collapse all

IQ Engine 10.3r3 is Now Available!

  • 1.  IQ Engine 10.3r3 is Now Available!

    Posted 06-16-2021 12:28

    IQ Engine 10.3r3 has been released! 

     

    You can view the release notes here.

     

    The downloadable files can be found on the Extreme Networks portal under Products:



  • 2.  RE: IQ Engine 10.3r3 is Now Available!

    Posted 06-18-2021 16:33

    Is 10.3r3 supposed to cap the power on Wifi1 at a max of 14? I upgrade 5 AP to test and all cap power at 14. 



  • 3.  RE: IQ Engine 10.3r3 is Now Available!

    Posted 06-18-2021 16:53

    caps @ 14 on DFS channels, 16 on lower 5 Ghz band (UNII-1), 18 on higher band (UNII-3). On 10.3r2 I got the most power on the DFS channels almost always got 20. 



  • 4.  RE: IQ Engine 10.3r3 is Now Available!

    Posted 06-18-2021 18:56

    That should be based on your country code more than the firmware version, but if you think it’s an issue with the new firmware I’d recommend pulling tech data on your current firmware, roll back to the firmware version you were on previously and get a tech data file from that version as well, and then open a case and submit both tech data files to the case so our engineers can compare the data. 



  • 5.  RE: IQ Engine 10.3r3 is Now Available!

    Posted 06-18-2021 19:11

    I already have a case open and I’ve already tested it. On 10.3r3 power on DFS channels caps at 14 as soon as you downgrade the firmware back to 10.3r2 the power comes up as 19. I’ve also tried a few reboots and switching channels on a single AP which is how I know what the max power will set to even if you manually chose 20 will set to. Updating the firmware doesn’t change the country code, right? I checked and 5 Ghz radio profiles don’t have a Country Code setting.



  • 6.  RE: IQ Engine 10.3r3 is Now Available!

    Posted 06-18-2021 19:13

    That is correct, updating the firmware won’t change the country code. You can see what country code you’re using currently with the command “show boot-param”.

     

    To change the country code, you’d need to request a call with support, that isn’t something you’d be able to adjust on your own.

     

    Or for anyone that doesn’t have support currently, I can help you with that as well, feel free to reach out to community@extremenetworks.com to set up a call to adjust the country code if needed. 



  • 7.  RE: IQ Engine 10.3r3 is Now Available!

    Posted 06-18-2021 19:27

    On 10.3r3

    boot parameters:
    Device IP:          0.0.0.0
    Netmask:            0.0.0.0
    TFTP Server IP:     0.0.0.0
    Gateway IP:         0.0.0.0
    VLAN ID:            0
    Native-VLAN ID:     0
    Netboot Always:     Disabled
    Netboot:            Disabled
    Boot File:
    Netdump:            Disabled
    Netdump File:       16501810170046.netdump
    Region Code:        FCC
    Country Code:       840
     

    On 10.3r2

    boot parameters:
    Device IP:          192.168.1.2
    Netmask:            255.255.255.0
    TFTP Server IP:     192.168.1.100
    Gateway IP:         192.168.1.254
    VLAN ID:            0
    Native-VLAN ID:     0
    Netboot Always:     Disabled
    Netboot:            Disabled
    Boot File:          AP650-mfg-20180829.img
    Netdump:            Disabled
    Netdump File:       ▒▒▒▒▒▒▒▒▒▒▒▒▒▒.netdump
    Region Code:        FCC
    Country Code:       840
     

    Country Code is the same



  • 8.  RE: IQ Engine 10.3r3 is Now Available!

    Posted 06-21-2021 12:02

    Setting this undocumented (or can’t seem to find any mention of it) item allows 10.3r3 to run above power 14 on 5 Ghz. It defaults to Outdoor I believe.

     



  • 9.  RE: IQ Engine 10.3r3 is Now Available!

    Posted 06-21-2021 12:23

    Actually, change Outdoor to indoor just caused the antenna setting to change back to default. In testing it just choosing the default antenna also allows the power setting to be set above 14 on DFS.



  • 10.  RE: IQ Engine 10.3r3 is Now Available!

    Posted 08-23-2021 22:01

    Where would I find this setting?



  • 11.  RE: IQ Engine 10.3r3 is Now Available!

    Posted 08-24-2021 09:36

    Devices - Configuration - Interface Settings - Wireless Interfaces



  • 12.  RE: IQ Engine 10.3r3 is Now Available!

    Posted 10-15-2021 16:08
    I do not have that setting. I'm using AP410C's with IQ engine 10.3.4.0