Data Center (VDX)

 View Only
  • 1.  Confirm how to configure logical-chassis mode

    Posted 11-28-2021 21:36
    Hi I'd like to confirm the correct command to configure a VDX6740 firmware 7.2.0c.
     
    I read in some older doco switch# vcs vcsid 1 rbridge-id 2 logical-chassis enable but this is not available and I can't recall the correct syntax and mode to execute this. 

    Thank you.


  • 2.  RE: Confirm how to configure logical-chassis mode

    Posted 11-29-2021 00:55
    Hi Russ,

    Starting NOS 7.1.x and higher, the only valid VCS mode is logical chassis which is enabled by default, so there's no need to configure logical-chassis enable anymoreYou just need to set the VCS ID and RB ID.


  • 3.  RE: Confirm how to configure logical-chassis mode

    Posted 11-29-2021 01:04
    Hi thanks for you reply. When I was checking the status after applying the VCSID and RB ID the output indicated that the switch was in VCS Mode : Fabric Cluster and not logical-chassis. 


  • 4.  RE: Confirm how to configure logical-chassis mode

    Posted 11-29-2021 01:13
    You will need to downgrade to 7.0.x, then set the vcs mode to logical chassis, then upgrade.


  • 5.  RE: Confirm how to configure logical-chassis mode

    Posted 11-29-2021 18:49
    Thanks again, for reference what was the command to configure logical-chassis mode?


  • 6.  RE: Confirm how to configure logical-chassis mode

    Posted 11-29-2021 22:05
    In 7.0.x, the command is the same as the one you posted in your first post: 

    vcs vcsid 1 rbridge-id 2 logical-chassis enable 


  • 7.  RE: Confirm how to configure logical-chassis mode

    Posted 12-02-2021 22:52
    Thanks for the info Truyen. 

    Something's gone south with the firmware downgrade, I'm now in a bootloop on the switches. I'm getting an output of the boot process ATM to post here.


  • 8.  RE: Confirm how to configure logical-chassis mode

    Posted 12-02-2021 23:09
    Edited by Russ 12-02-2021 23:09
    the boot up messages attached.-------------------------------------------

    =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2021.12.03 14:45:35 =~=~=~=~=~=~=~=~=~=~=~=


    BootROM version: 1.0.76
    Copyright (C) 2011 Brocade Communication.

    CPU0: P3041, Version: 2.0, (0x82110320)
    Core: E500MC, Version: 3.2, (0x80230032)
    Clock Configuration:
    CPU0:1499.400 MHz, CPU1:1499.400 MHz, CPU2:1499.400 MHz, CPU3:1499.400 MHz,
    CCB:749.700 MHz,
    DDR:499.800 MHz (999.600 MT/s data rate) (Asynchronous), LBC:46.856 MHz
    FMAN1: 374.850 MHz
    PME: 374.850 MHz
    L1: D-cache 32 kB enabled
    I-cache 32 kB enabled
    Model ID: 131
    Board: P3041 CASTOR, 36-bit Addressing
    reset reason was 0x00000001: Power Up
    I2C: ready
    DRAM: Initializing....
    Enabled DHC_EN
    FSL_ERRATUM_DDR_A003 workaround applied
    DIMM 0 [0xfe008174=0x8675a607] [0xfe008f38=0x11110e0c] [0xfe008f3c=0x0b0d0e10] [0xfe008f40=0x0d004004]
    6 GiB left unmapped
    DDR: 8 GiB (DDR3, 64-bit, CL=7, ECC on)
    testdram value not set, dram test not run
    Now running in RAM - U-Boot at: 7ff20000
    FLASH: 4 MiB
    L2: 128 KB enabled
    Corenet Platform Cache: 1024 KB enabled
    SERDES: bank 2 disabled
    PCI: gd->brcd_flags = 0, PCI init
    PCIE1 connected to Slot 1 as Root Complex (base addr fe200000)
    Scanning PCI bus 01
    PCIE0 on bus 00 - 01

    MMK configuring pit regs
    In: serial
    Out: serial
    Err: serial
    SRIO1: disabled
    SRIO2: disabled
    NVRAM/RTC oscillator already turned on in a previous boot
    Net: Fman: Uploading microcode version 101.6.0.
    FM1@DTSEC4, FM1@DTSEC5
    usb reset 0
    (Re)start USB 0...
    USB: Register 10011 NbrPorts 1
    USB EHCI 1.00
    scanning bus for devices... Manufacturer u-boot
    Product EHCI Host Controller
    SerialNumber
    Manufacturer Generic
    Product Flash Card Reader
    SerialNumber 000000225001
    2 USB Device(s) found
    scanning bus for storage devices... 1 Storage Device(s) found
    setting prt to 2
    Hit ESC to stop autoboot: 5 4 3 2 1 0
    Loading Environment 1 from NVRAM...
    (Re)start USB 0...
    USB: Register 10011 NbrPorts 1
    USB EHCI 1.00
    scanning bus for devices... Manufacturer u-boot
    Product EHCI Host Controller
    SerialNumber
    Manufacturer Generic
    Product Flash Card Reader
    SerialNumber 000000225001
    2 USB Device(s) found
    scanning bus for storage devices... 1 Storage Device(s) found
    setting prt to 2
    Loading Environment 0 from NVRAM...
    (Re)start USB 0...
    USB: Register 10011 NbrPorts 1
    USB EHCI 1.00
    scanning bus for devices... Manufacturer u-boot
    Product EHCI Host Controller
    SerialNumber
    Manufacturer Generic
    Product Flash Card Reader
    SerialNumber 000000225001
    2 USB Device(s) found
    scanning bus for storage devices... 1 Storage Device(s) found
    setting prt to 2
    Loading file "/boot/fastloading.mdt" from usb device 0:2 (usbda2)
    158 bytes read
    Image: [uImage]
    Image: [hv.uImage]
    Image: [silkworm.dtb]
    Image: [silkworm_hct.dtb]
    WARNING: adjusting available memory to 30000000
    ## Booting kernel from Legacy Image at 02000000 ...
    Image Name:
    Image Type: PowerPC Linux Kernel Image (uncompressed)
    Data Size: 473624 Bytes = 462.5 KiB
    Load Address: 00000000
    Entry Point: 00000000
    Verifying Checksum ... OK
    ## Flattened Device Tree blob at 04000000
    Booting using the fdt blob at 0x4000000
    Loading Kernel Image ... OK
    OK
    Loading Device Tree to 00ff7000, end 00fff22b ... OK
    =======================================
    Freescale Hypervisor 0.8-004
    Hypervisor command line: config-addr=0x3000000 p1-linux="root=/dev/sda2 rootfstype=ext4 quiet" p2-linux="root=/dev/sda2 rootfstype=ext4 quiet ip=bootp"
    [0] malloc_init: using 31 MiB at 0x7e0e38b0 - 0x7fffffff
    Brocade PB device tree:brocade,SILKWORM_PB
    Got liodn 125
    [0] assign_callback: device serial0 in serial0 not found
    [0] assign_callback: device /hvcpld in fpga not found
    USB:
    Static Qhead=0x4d60c0 Qhead list=0x4d6140 Qtd base=0x4d61c0

    Static Qhead Align=[0] Qhead list Align=[0] Qtd base=[0]
    Register 10011 NbrPorts 1
    hv scanning bus for usb devices... 2 USB Device(s) found
    [0] watchdog enabled with period 38
    HV> Hypervisor scanning bus for storage devices...
    HV> ========Storage Device Details==========
    HV> Mfr=Generic, Product=Flash Card Reader, SerialNumber=000000225001
    HV> 1 HV Storage Device(s) found
    HV> Init hypervisor timer init_timer:8
    HV> [1] watchdog enabled with period 38
    [2] watchdog enabled with period 38
    HV> [3] watchdog enabled with period 38
    HV> [2] Virtual Storage thread=7e22d210
    HV> [0] get_rpn: mem-range has discontiguity at guest address 0x68000000.
    HV>
    part_start 2 2

    dev_name vs_attach_guest /vsmgr/vd@usb0/vda01 part_start 2 no_of_parts 2

    [vs_attach_guest]vdisk->start 0x74f7ff vdisk->size 0x74e801

    [vs_attach_guest]vdisk->start 0x74f7ff vdisk->size 0x74e801
    Bootargs set for cpu = 2 guest p2-linux bootagrs = root=/dev/sda2 rootfstype=ext4 quiet ip=bootp

    part2 STANDBY
    HV>
    part_start 0 2
    HV>
    dev_name vs_attach_guest /vsmgr/vd@usb0/vda00 part_start 0 no_of_parts 2
    HV>
    [vs_attach_guest]vdisk->start 0x0 vdisk->size 0x74f000
    HV>
    [vs_attach_guest]vdisk->start 0x0 vdisk->size 0x74f000
    HV> Bootargs set for cpu = 0 guest p1-linux bootagrs = root=/dev/sda2 rootfstype=ext4 quiet
    HV>
    part1 ACTIVE
    HV> [0] Clearing standby console log
    HV> patch_pcie_msi_guest_node:set p2-linux msi0
    HV> patch_pcie_msi_guest_node: set msi-address-64 f0000740
    HV> b [0] loading binary image from 0x79fff000 to 0x3000000
    HV> [2] loading binary image from 0x79fff000 to 0x3000000
    [0] Loading uImage from 0x78000000 to 0
    HV> [2] Loading uImage from 0x78000000 to 0
    HV> [2] branching to guest p2-linux, 2 cpus
    HV> [0] branching to guest p1-linux, 2 cpus
    HV> this is quiet!

    end of DRAM 4294967296 memstart_addr0 total_lowmem 4294967296
    Using /devices/qman property 'fsl,qman-fqd'
    it's a 'zero-pma', not zeroing from s/w
    Using /devices/qman property 'fsl,qman-pfdr'
    Qman ver:0a01,01,02
    Treating Qman ver:01,02 as 0x0101
    -> DMA enabled

    [silkworm_setup_pci_shared_memory]config_done 0 scandone 0 pcilcok 0x0
    SLUB: dfree enabled
    PRIMING SLUB: main caches
    SLUB: export __kmalloc at 0x40113658 changed to 0x40113a60
    SLUB: export vmalloc at 0x400f72c4 changed to 0x400f7078
    SLUB: export vfree at 0x400f63d0 changed to 0x400f6300
    network namespace NR (VRF) started

    PCI_PROBE_DEVTREE

    PCI_PROBE_DEVTREE
    Qman registered for failover, is currently active
    Qman err interrupt handler present
    Treating Qman portal ver:0x0102 as 0x0101
    Qman portal at c1020000:c101e000 (0:0,v0101)
    Qman portal initialised, cpu 0
    Treating Qman portal ver:0x0102 as 0x0101
    Qman portal at c1028000:c1026000 (1:1,v0101)
    Qman portal initialised, cpu 1
    before calling: qman_release_fqid_range 512:256
    Qman: FQID allocator includes range 512:256
    Qman driver initialised
    mmod_sysctl_inited: 1
    ***** pcie_portdrv_init: active completed
    cpu1/1: failover_register() - registering notifiers...

    Fman microcode 51 45 46

    FMAN microcode UC size 0x1b64
    default MII is 0xc10a8000 for tsec0
    gtg_init:Coldboot case
    gtg_init(1):Ring bf4f6800 Peer Ring becf6800
    Uboot wdt counter value: 0
    VSD Created with major number vsd_probe = 254

    disk->start 0 cmd->start 0 nstart 0 disk name /vsmgr/vd@usb0/vda00
    HV>
    create_new_partition_table part_no 0 no_of_parts 2
    HV> INIT: version 2.78 booting
    Firmware Integrity Check is default off
    Bypassing firmware validation.
    mount: sysfs already mounted or /sys busy
    mount: according to mtab, none is already mounted on /sys
    mknod: /dev/fsl-hv: File exists
    Hostname is sw0
    INIT: Entering runlevel: 3
    FIPS-mode test application

    1. Non-Approved cryptographic operation test...
    a. Excluded algorithm (MD5)...successful

    Automatic Power-Up Self Tests...

    1. DH...successful
    2. FIPS RNG (AES_256_CTR_DRBG) selftest...successful
    3. AES-128,192,256 CBC encryption/decryption...successful
    4. RSA key generation and encryption/decryption...successful
    a. RSA 2048 with 'SHA256' testing...successful
    5. TDES-CBC encryption/decryption...successful
    6. HASH and HMAC tests...
    a. SHA-1 hash...successful
    b. SHA-256 hash...successful
    c. SHA-384 hash...successful
    d. SHA-512 hash...successful
    e. HMAC-SHA-1 hash...successful
    f. HMAC-SHA-224 hash...successful
    g. HMAC-SHA-256 hash...successful
    h. HMAC-SHA-384 hash...successful
    i. HMAC-SHA-512 hash...successful
    7. Zero-ization...Successful
    8. ECDSA ...successful
    9. ECDH ...successful
    10. TLS KDF 1.0...successful
    10a. TLS KDF 1.2...successful
    11. SSH KDF...successful
    sysmodAttach open failed: No such device or address
    sysmodAttach open failed: No such device or address
    system_parameter_init: sysModInit() failed(2)12. SNMP KDF...successful

    All tests completed with 0 errors
    GTG Peer GOS reset
    (none)
    Waiting to starting configuration management service
    Starting configuration management service
    [wmd_init]: chunk_size = 0xa00000
    [wmd_init]: WM reset
    Found 1(threshold 5) abnormal reboots within 5000 seconds window(threshold)
    KernelSpace rastrace_register
    DCM MODE:0x0
    SWBD module launch ... Fri Dec 3 03:10:30 GMT 2021
    CPLD INIT DONE
    SEEPROM Read Done!
    Cobra rev B found
    Info: panic dump has been initialized!
    Starting HASM ... Fri Dec 3 03:10:47 GMT 2021
    LAUNCH HASMD 131 0x0 0Exisitng reboot reason fsize = 5 rb=
    Global Fan Direction: Port Side EXHAUST



    Network OS (sw0)
    sw0 console login: Castor: PCIe Err handler init plat_pci_init[800]
    bhpc_irq_init: Using default device map. Size 10
    bhpc_irq_init: Pcie domain 0 err interrupt handler Installed
    Starting Dcmd ... Fri Dec 3 03:10:50 GMT 2021
    server starting
    Restoring DCM database2048 indexes lost
    .free list corrupted, idx 651 already assigned!
    .tp_register, got none fss tp handle=10000001h
    2021/12/03-03:10:55, [HSL-1012], 1, INFO, VDX6740, Interface lo is link up
    2021/12/03-03:10:55, [HSL-1012], 2, INFO, VDX6740, Interface eth0 is link up
    2021/12/03-03:10:55, [HSL-1012], 3, INFO, VDX6740, Interface eth1 is link up
    2021/12/03-03:10:55, [HASM-1004], 4, INFO, VDX6740, Processor reloaded - Reset.
    .....done

    disk->start 7665663 cmd->start 0 nstart 7665663 disk name /vsmgr/vd@usb0/vda01
    HV>
    create_new_partition_table part_no 2 no_of_parts 2
    HV> [3] restart_guest_remap: self is calling remap_restart_unc due to standby and hcall_partition_restart_ha.
    HV> [2] loading binary image from 0x79fff000 to 0x3000000
    HV> [2] Loading uImage from 0x78000000 to 0
    HV> [2] branching to guest p2-linux, 2 cpus
    HV> GTG Peer GOS reset
    waiting for server to shut down............................... done
    server stopped

    disk->start 7665663 cmd->start 0 nstart 7665663 disk name /vsmgr/vd@usb0/vda01
    HV>
    create_new_partition_table part_no 2 no_of_parts 2
    HV> [3] Hypervisor Resetting due to: hcall_system_reset
    [3]
    Hypervisor Reset Flush:

    HV>

    BootROM version: 1.0.76
    Copyright (C) 2011 Brocade Communication.

    CPU0: P3041, Version: 2.0, (0x82110320)
    Core: E500MC, Version: 3.2, (0x80230032)
    Clock Configuration:
    CPU0:1499.400 MHz, CPU1:1499.400 MHz, CPU2:1499.400 MHz, CPU3:1499.400 MHz,
    CCB:749.700 MHz,
    DDR:499.800 MHz (999.600 MT/s data rate) (Asynchronous), LBC:46.856 MHz
    FMAN1: 374.850 MHz
    PME: 374.850 MHz
    L1: D-cache 32 kB enabled
    I-cache 32 kB enabled
    Model ID: 131
    Board: P3041 CASTOR, 36-bit Addressing
    reset reason was 0x00000002: CPU request
    I2C: ready
    DRAM: Initializing....
    Enabled DHC_EN
    FSL_ERRATUM_DDR_A003 workaround applied
    DIMM 0 [0xfe008174=0x8675a607] [0xfe008f38=0x11110e0c] [0xfe008f3c=0x0b0d0e10] [0xfe008f40=0x0d004004]
    6 GiB left unmapped
    DDR: 8 GiB (DDR3, 64-bit, CL=7, ECC on)
    testdram value not set, dram test not run
    Now running in RAM - U-Boot at: 7ff20000
    FLASH: 4 MiB
    L2: 128 KB enabled
    Corenet Platform Cache: 1024 KB enabled
    SERDES: bank 2 disabled
    PCI: gd->brcd_flags = 0, PCI init
    PCIE1 connected to Slot 1 as Root Complex (base addr fe200000)
    Scanning PCI bus 01
    PCIE0 on bus 00 - 01

    MMK configuring pit regs
    In: serial
    Out: serial
    Err: serial
    SRIO1: disabled
    SRIO2: disabled
    NVRAM/RTC oscillator already turned on in a previous boot
    Net: Fman: Uploading microcode version 101.6.0.
    FM1@DTSEC4, FM1@DTSEC5
    usb reset 0
    (Re)start USB 0...
    USB: Register 10011 NbrPorts 1
    USB EHCI 1.00
    scanning bus for devices... Manufacturer u-boot
    Product EHCI Host Controller
    SerialNumber
    Manufacturer Generic
    Product Flash Card Reader
    SerialNumber 000000225001
    2 USB Device(s) found
    scanning bus for storage devices... 1 Storage Device(s) found
    setting prt to 2
    Hit ESC to stop autoboot: 5 4 3 2 1 0
    Loading Environment 1 from NVRAM...
    (Re)start USB 0...
    USB: Register 10011 NbrPorts 1
    USB EHCI 1.00
    scanning bus for devices... Manufacturer u-boot
    Product EHCI Host Controller
    SerialNumber
    Manufacturer Generic
    Product Flash Card Reader
    SerialNumber 000000225001
    2 USB Device(s) found
    scanning bus for storage devices... 1 Storage Device(s) found
    setting prt to 2
    Loading Environment 0 from NVRAM...
    (Re)start USB 0...
    USB: Register 10011 NbrPorts 1
    USB EHCI 1.00
    scanning bus for devices... Manufacturer u-boot
    Product EHCI Host Controller
    SerialNumber
    Manufacturer Generic
    Product Flash Card Reader
    SerialNumber 000000225001
    2 USB Device(s) found
    scanning bus for storage devices... 1 Storage Device(s) found
    setting prt to 2
    Loading file "/boot/fastloading.mdt" from usb device 0:2 (usbda2)
    158 bytes read
    Image: [uImage]
    Image: [hv.uImage]
    Image: [silkworm.dtb]
    Image: [silkworm_hct.dtb]
    WARNING: adjusting available memory to 30000000
    ## Booting kernel from Legacy Image at 02000000 ...
    Image Name:
    Image Type: PowerPC Linux Kernel Image (uncompressed)
    Data Size: 473624 Bytes = 462.5 KiB
    Load Address: 00000000
    Entry Point: 00000000
    Verifying Checksum ... OK
    ## Flattened Device Tree blob at 04000000
    Booting using the fdt blob at 0x4000000
    Loading Kernel Image ... OK
    OK
    Loading Device Tree to 00ff7000, end 00fff22b ... OK
    =======================================
    Freescale Hypervisor 0.8-004
    Hypervisor command line: config-addr=0x3000000 p1-linux="root=/dev/sda2 rootfstype=ext4 quiet" p2-linux="root=/dev/sda2 rootfstype=ext4 quiet ip=bootp"
    [0] malloc_init: using 31 MiB at 0x7e0e38b0 - 0x7fffffff
    Brocade PB device tree:brocade,SILKWORM_PB
    Got liodn 125
    [0] assign_callback: device serial0 in serial0 not found
    [0] assign_callback: device /hvcpld in fpga not found
    USB:
    Static Qhead=0x4d60c0 Qhead list=0x4d6140 Qtd base=0x4d61c0

    Static Qhead Align=[0] Qhead list Align=[0] Qtd base=[0]
    Register 10011 NbrPorts 1
    hv scanning bus for usb devices... 2 USB Device(s) found
    [0] watchdog enabled with period 38
    HV> Hypervisor scanning bus for storage devices...
    HV> ========Storage Device Details==========
    HV> Mfr=Generic, Product=Flash Card Reader, SerialNumber=000000225001
    HV> 1 HV Storage Device(s) found
    HV> Init hypervisor timer init_timer:8
    HV> [1] watchdog enabled with period 38
    [2] watchdog enabled with period 38
    HV> [3] watchdog enabled with period 38
    HV> [2] Virtual Storage thread=7e22d210
    HV> [0] get_rpn: mem-range has discontiguity at guest address 0x68000000.
    HV>
    part_start 2 2

    dev_name vs_attach_guest /vsmgr/vd@usb0/vda01 part_start 2 no_of_parts 2

    [vs_attach_guest]vdisk->start 0x74f7ff vdisk->size 0x74e801

    [vs_attach_guest]vdisk->start 0x74f7ff vdisk->size 0x74e801
    Bootargs set for cpu = 2 guest p2-linux bootagrs = root=/dev/sda2 rootfstype=ext4 quiet ip=bootp

    part2 STANDBY
    HV>
    part_start 0 2
    HV>
    dev_name vs_attach_guest /vsmgr/vd@usb0/vda00 part_start 0 no_of_parts 2
    HV>
    [vs_attach_guest]vdisk->start 0x0 vdisk->size 0x74f000
    HV>
    [vs_attach_guest]vdisk->start 0x0 vdisk->size 0x74f000
    HV> Bootargs set for cpu = 0 guest p1-linux bootagrs = root=/dev/sda2 rootfstype=ext4 quiet
    HV>
    part1 ACTIVE
    HV> [0] Clearing standby console log
    HV> patch_pcie_msi_guest_node:set p2-linux msi0
    HV> b patch_pcie_msi_guest_node: set msi-address-64 f0000740
    HV> [0] loading binary image from 0x79fff000 to 0x3000000
    HV> [2] loading binary image from 0x79fff000 to 0x3000000
    [0] Loading uImage from 0x78000000 to 0
    HV> [2] Loading uImage from 0x78000000 to 0
    HV> [2] branching to guest p2-linux, 2 cpus
    HV> [0] branching to guest p1-linux, 2 cpus
    HV> this is quiet!

    end of DRAM 4294967296 memstart_addr0 total_lowmem 4294967296
    Using /devices/qman property 'fsl,qman-fqd'
    it's a 'zero-pma', not zeroing from s/w
    Using /devices/qman property 'fsl,qman-pfdr'
    Qman ver:0a01,01,02
    Treating Qman ver:01,02 as 0x0101
    -> DMA enabled

    [silkworm_setup_pci_shared_memory]config_done 0 scandone 0 pcilcok 0x0
    SLUB: dfree enabled
    PRIMING SLUB: main caches
    SLUB: export __kmalloc at 0x40113658 changed to 0x40113a60
    SLUB: export vmalloc at 0x400f72c4 changed to 0x400f7078
    SLUB: export vfree at 0x400f63d0 changed to 0x400f6300
    network namespace NR (VRF) started

    PCI_PROBE_DEVTREE

    PCI_PROBE_DEVTREE
    Qman registered for failover, is currently active
    Qman err interrupt handler present
    Treating Qman portal ver:0x0102 as 0x0101
    Qman portal at c1020000:c101e000 (0:0,v0101)
    Qman portal initialised, cpu 0
    Treating Qman portal ver:0x0102 as 0x0101
    Qman portal at c1028000:c1026000 (1:1,v0101)
    Qman portal initialised, cpu 1
    before calling: qman_release_fqid_range 512:256
    Qman: FQID allocator includes range 512:256
    Qman driver initialised
    mmod_sysctl_inited: 1
    ***** pcie_portdrv_init: active completed
    cpu0/0: failover_register() - registering notifiers...

    Fman microcode 51 45 46

    FMAN microcode UC size 0x1b64
    default MII is 0xc10a8000 for tsec0
    gtg_init:Coldboot case
    gtg_init(1):Ring bf4f6800 Peer Ring becf6800
    Uboot wdt counter value: 0
    VSD Created with major number vsd_probe = 254

    disk->start 0 cmd->start 0 nstart 0 disk name /vsmgr/vd@usb0/vda00
    HV>
    create_new_partition_table part_no 0 no_of_parts 2
    HV> INIT: version 2.78 booting
    Firmware Integrity Check is default off
    Bypassing firmware validation.
    mount: sysfs already mounted or /sys busy
    mount: according to mtab, none is already mounted on /sys
    mknod: /dev/fsl-hv: File exists
    Hostname is sw0
    INIT: Entering runlevel: 3
    FIPS-mode test application

    1. Non-Approved cryptographic operation test...
    a. Excluded algorithm (MD5)...successful

    Automatic Power-Up Self Tests...

    1. DH...successful
    2. FIPS RNG (AES_256_CTR_DRBG) selftest...successful
    3. AES-128,192,256 CBC encryption/decryption...successful
    4. RSA key generation and encryption/decryption...successful
    a. RSA 2048 with 'SHA256' testing...successful
    5. TDES-CBC encryption/decryption...successful
    6. HASH and HMAC tests...
    a. SHA-1 hash...successful
    b. SHA-256 hash...successful
    c. SHA-384 hash...successful
    d. SHA-512 hash...successful
    e. HMAC-SHA-1 hash...successful
    f. HMAC-SHA-224 hash...successful
    g. HMAC-SHA-256 hash...successful
    h. HMAC-SHA-384 hash...successful
    i. HMAC-SHA-512 hash...successful
    7. Zero-ization...Successful
    8. ECDSA ...successful
    9. ECDH ...successful
    10. TLS KDF 1.0...successful
    10a. TLS KDF 1.2...successful
    11. SSH KDF...successful
    sysmodAttach open failed: No such device or address
    sysmodAttach open failed: No such device or address
    system_parameter_init: sysModInit() failed(2)12. SNMP KDF...successful

    All tests completed with 0 errors
    GTG Peer GOS reset
    (none)
    Waiting to starting configuration management service
    Starting configuration management service
    [wmd_init]: chunk_size = 0xa00000
    [wmd_init]: WM reset
    Found 2(threshold 5) abnormal reboots within 5000 seconds window(threshold)
    KernelSpace rastrace_register
    DCM MODE:0x0
    SWBD module launch ... Fri Dec 3 03:17:28 GMT 2021
    CPLD INIT DONE
    SEEPROM Read Done!
    Cobra rev B found
    Info: panic dump has been initialized!
    Starting HASM ... Fri Dec 3 03:17:46 GMT 2021
    LAUNCH HASMD 131 0x0 0Exisitng reboot reason fsize = 5 rb=



    Network OS (sw0)
    sw0 console login: Global Fan Direction: Port Side EXHAUST
    Castor: PCIe Err handler init plat_pci_init[800]
    bhpc_irq_init: Using default device map. Size 10
    bhpc_irq_init: Pcie domain 0 err interrupt handler Installed
    Starting Dcmd ... Fri Dec 3 03:17:51 GMT 2021
    tp_register, got none fss tp handle=10000001h
    2021/12/03-03:17:53, [HSL-1012], 5, INFO, VDX6740, Interface lo is link up
    2021/12/03-03:17:53, [HSL-1012], 6, INFO, VDX6740, Interface eth0 is link up
    2021/12/03-03:17:53, [HSL-1012], 7, INFO, VDX6740, Interface eth1 is link up
    2021/12/03-03:17:53, [HASM-1004], 8, INFO, VDX6740, Processor reloaded - Reset.
    server starting
    Restoring DCM database...done




    Network OS (sw0)
    sw0 console login: admin


    Password:

    2021/12/03-03:18:22, [SEC-1206], 9, SW/0 | Active, INFO, sw0, Login information: User [admin] Last Successful Login Time : Fri Dec 3 01:08:31 2021
    .
    Error: Network OS is not ready. Please login later.
    2021/12/03-03:18:23, [SEC-3022], 10, SW/0 | Active, INFO, sw0, Event: logout, Status: success, Info: Successful logout by user [admin].



    Network OS (sw0)
    sw0 console login:
    disk->start 7665663 cmd->start 0 nstart 7665663 disk name /vsmgr/vd@usb0/vda01
    HV>
    create_new_partition_table part_no 2 no_of_parts 2
    HV> [3] restart_guest_remap: self is calling remap_restart_unc due to standby and hcall_partition_restart_ha.
    HV> [2] loading binary image from 0x79fff000 to 0x3000000
    HV> [2] Loading uImage from 0x78000000 to 0
    HV> [2] branching to guest p2-linux, 2 cpus
    HV> GTG Peer GOS reset
    waiting for server to shut down........................ done
    server stopped
    Fri Dec 3 03:23:28 GMT 2021 :: Confd: Waiting for Dcmd to become ready...
    Services starting COLD recovery
    CHASSIS RECOV_ACTIVE
    Activating Route Profile [RTPROFILE_TYPE_DEFAULT], ecmp [0]
    Activating HW Profile [HWPROFILE_TYPE_DEFAULT]
    Activating KAP Profile [DEFAULT]
    SNMP Research EMANATE/Lite Agent Version 16.2.0.9
    Copyright 1989-2006 SNMP Research, Inc.
    dcm init successful
    Confd: No need to wait for Ccmd...
    Fri Dec 3 03:23:43 GMT 2021 :: Triggering confd load phase1 after waiting for 10 secs

    disk->start 7665663 cmd->start 0 nstart 7665663 disk name /vsmgr/vd@usb0/vda01
    HV>
    create_new_partition_table part_no 2 no_of_parts 2
    HV> Passed :: register_for_publisher_notification for MSG_TNL_GW_CONF_NOTIFY passed for NSMD.
    Subsribed successfully for NSMPORTDECFGMSG in rmond
    radv trace initialization succeeded.
    srm trace initialization succeeded.
    arp trace initialization succeeded.
    vrrp_tha_init: regdone handle 1
    ARP trace init Successful
    VRRP_tha_Init: stage 1 done
    ribmgr trace initialization succeeded.
    pcap_master_init - sm is NULL after ha_calloc
    rps trace initialization succeeded.
    [3] Hypervisor Resetting due to: hcall_system_reset

    ++++++++++++++++++++++++++++++++++++++++++++++++++++

    Current Mode of Op:interrupt Vs Thread State:0x2 blockPos:4
    Current Active cookie Gos0:21917 Gos1:2168
    Current Queued max cookie Gos0:21918 Gos1:2168
    Guest sem info data 0x0 waitlist 0x0
    ++++++++++++++++++++++++++++++++++++++++++++++++++++
    HV>
    calling system reset from vs_thread_worker:
    [2]
    Hypervisor Reset Flush:

    HV>
    since guest is stopping don't accept any io:hcall_submit_aio
    HV>

    BootROM version: 1.0.76
    Copyright (C) 2011 Brocade Communication.

    CPU0: P3041, Version: 2.0, (0x82110320)
    Core: E500MC, Version: 3.2, (0x80230032)
    Clock Configuration:
    CPU0:1499.400 MHz, CPU1:1499.400 MHz, CPU2:1499.400 MHz, CPU3:1499.400 MHz,
    CCB:749.700 MHz,
    DDR:499.800 MHz (999.600 MT/s data rate) (Asynchronous), LBC:46.856 MHz
    FMAN1: 374.850 MHz
    PME: 374.850 MHz
    L1: D-cache 32 kB enabled
    I-cache 32 kB enabled
    Model ID: 131
    Board: P3041 CASTOR, 36-bit Addressing
    reset reason was 0x00000002: CPU request
    I2C: ready
    DRAM: Initializing....
    Enabled DHC_EN
    FSL_ERRATUM_DDR_A003 workaround applied
    DIMM 0 [0xfe008174=0x8675a607] [0xfe008f38=0x11110e0c] [0xfe008f3c=0x0b0d0e10] [0xfe008f40=0x0d004004]
    6 GiB left unmapped
    DDR: 8 GiB (DDR3, 64-bit, CL=7, ECC on)
    testdram value not set, dram test not run
    Now running in RAM - U-Boot at: 7ff20000
    FLASH: 4 MiB
    L2: 128 KB enabled
    Corenet Platform Cache: 1024 KB enabled
    SERDES: bank 2 disabled
    PCI: gd->brcd_flags = 0, PCI init
    PCIE1 connected to Slot 1 as Root Complex (base addr fe200000)
    Scanning PCI bus 01
    PCIE0 on bus 00 - 01

    MMK configuring pit regs
    In: serial
    Out: serial
    Err: serial
    SRIO1: disabled
    SRIO2: disabled
    NVRAM/RTC oscillator already turned on in a previous boot
    Net: Fman: Uploading microcode version 101.6.0.
    FM1@DTSEC4, FM1@DTSEC5
    usb reset 0
    (Re)start USB 0...
    USB: Register 10011 NbrPorts 1
    USB EHCI 1.00
    scanning bus for devices... Manufacturer u-boot
    Product EHCI Host Controller
    SerialNumber
    Manufacturer Generic
    Product Flash Card Reader
    SerialNumber 000000225001
    2 USB Device(s) found
    scanning bus for storage devices... 1 Storage Device(s) found
    setting prt to 2
    Hit ESC to stop autoboot: 5 4 3 2 1 0
    Loading Environment 1 from NVRAM...
    (Re)start USB 0...
    USB: Register 10011 NbrPorts 1
    USB EHCI 1.00
    scanning bus for devices... Manufacturer u-boot
    Product EHCI Host Controller
    SerialNumber
    Manufacturer Generic
    Product Flash Card Reader
    SerialNumber 000000225001
    2 USB Device(s) found
    scanning bus for storage devices... 1 Storage Device(s) found
    setting prt to 2
    Loading Environment 0 from NVRAM...
    (Re)start USB 0...
    USB: Register 10011 NbrPorts 1
    USB EHCI 1.00
    scanning bus for devices... Manufacturer u-boot
    Product EHCI Host Controller
    SerialNumber
    Manufacturer Generic
    Product Flash Card Reader
    SerialNumber 000000225001
    2 USB Device(s) found
    scanning bus for storage devices... 1 Storage Device(s) found
    setting prt to 2
    Loading file "/boot/fastloading.mdt" from usb device 0:2 (usbda2)
    158 bytes read
    Image: [uImage]
    Image: [hv.uImage]
    Image: [silkworm.dtb]
    Image: [silkworm_hct.dtb]
    WARNING: adjusting available memory to 30000000
    ## Booting kernel from Legacy Image at 02000000 ...
    Image Name:
    Image Type: PowerPC Linux Kernel Image (uncompressed)
    Data Size: 473624 Bytes = 462.5 KiB
    Load Address: 00000000
    Entry Point: 00000000
    Verifying Checksum ... OK
    ## Flattened Device Tree blob at 04000000
    Booting using the fdt blob at 0x4000000
    Loading Kernel Image ... OK
    OK
    Loading Device Tree to 00ff7000, end 00fff22b ... OK
    =======================================
    Freescale Hypervisor 0.8-004
    Hypervisor command line: config-addr=0x3000000 p1-linux="root=/dev/sda2 rootfstype=ext4 quiet" p2-linux="root=/dev/sda2 rootfstype=ext4 quiet ip=bootp"
    [0] malloc_init: using 31 MiB at 0x7e0e38b0 - 0x7fffffff
    Brocade PB device tree:brocade,SILKWORM_PB
    Got liodn 125
    [0] assign_callback: device serial0 in serial0 not found
    [0] assign_callback: device /hvcpld in fpga not found
    USB:
    Static Qhead=0x4d60c0 Qhead list=0x4d6140 Qtd base=0x4d61c0

    Static Qhead Align=[0] Qhead list Align=[0] Qtd base=[0]
    Register 10011 NbrPorts 1
    hv scanning bus for usb devices... 2 USB Device(s) found
    [0] watchdog enabled with period 38
    HV> Hypervisor scanning bus for storage devices...
    HV> ========Storage Device Details==========
    HV> Mfr=Generic, Product=Flash Card Reader, SerialNumber=000000225001
    HV> 1 HV Storage Device(s) found
    HV> Init hypervisor timer init_timer:8
    HV> [1] watchdog enabled with period 38
    [2] watchdog enabled with period 38
    HV> [3] watchdog enabled with period 38
    HV> [2] Virtual Storage thread=7e22d210
    HV> [0] get_rpn: mem-range has discontiguity at guest address 0x68000000.
    HV>
    part_start 2 2

    dev_name vs_attach_guest /vsmgr/vd@usb0/vda01 part_start 2 no_of_parts 2

    [vs_attach_guest]vdisk->start 0x74f7ff vdisk->size 0x74e801

    [vs_attach_guest]vdisk->start 0x74f7ff vdisk->size 0x74e801
    Bootargs set for cpu = 2 guest p2-linux bootagrs = root=/dev/sda2 rootfstype=ext4 quiet ip=bootp
    HV>
    part2 STANDBY
    HV>
    part_start 0 2
    HV>
    dev_name vs_attach_guest /vsmgr/vd@usb0/vda00 part_start 0 no_of_parts 2
    HV>
    [vs_attach_guest]vdisk->start 0x0 vdisk->size 0x74f000
    HV>
    [vs_attach_guest]vdisk->start 0x0 vdisk->size 0x74f000
    HV> Bootargs set for cpu = 0 guest p1-linux bootagrs = root=/dev/sda2 rootfstype=ext4 quiet
    HV>
    part1 ACTIVE
    HV> [0] Clearing standby console log
    patch_pcie_msi_guest_node:set p2-linux msi0
    HV> patch_pcie_msi_guest_node: set msi-address-64 f0000740
    HV> b [0] loading binary image from 0x79fff000 to 0x3000000
    HV> [2] loading binary image from 0x79fff000 to 0x3000000
    [0] Loading uImage from 0x78000000 to 0
    HV> [2] Loading uImage from 0x78000000 to 0
    HV> [2] branching to guest p2-linux, 2 cpus
    HV> [0] branching to guest p1-linux, 2 cpus
    HV> this is quiet!

    end of DRAM 4294967296 memstart_addr0 total_lowmem 4294967296
    Using /devices/qman property 'fsl,qman-fqd'
    it's a 'zero-pma', not zeroing from s/w
    Using /devices/qman property 'fsl,qman-pfdr'
    Qman ver:0a01,01,02
    Treating Qman ver:01,02 as 0x0101
    -> DMA enabled

    [silkworm_setup_pci_shared_memory]config_done 0 scandone 0 pcilcok 0x0
    SLUB: dfree enabled
    PRIMING SLUB: main caches
    SLUB: export __kmalloc at 0x40113658 changed to 0x40113a60
    SLUB: export vmalloc at 0x400f72c4 changed to 0x400f7078
    SLUB: export vfree at 0x400f63d0 changed to 0x400f6300
    network namespace NR (VRF) started

    PCI_PROBE_DEVTREE

    PCI_PROBE_DEVTREE
    Qman registered for failover, is currently active
    Qman err interrupt handler present
    Treating Qman portal ver:0x0102 as 0x0101
    Qman portal at c1020000:c101e000 (0:0,v0101)
    Qman portal initialised, cpu 0
    Treating Qman portal ver:0x0102 as 0x0101
    Qman portal at c1028000:c1026000 (1:1,v0101)
    Qman portal initialised, cpu 1
    before calling: qman_release_fqid_range 512:256
    Qman: FQID allocator includes range 512:256
    Qman driver initialised
    mmod_sysctl_inited: 1
    ***** pcie_portdrv_init: active completed
    cpu1/1: failover_register() - registering notifiers...

    Fman microcode 51 45 46

    FMAN microcode UC size 0x1b64
    default MII is 0xc10a8000 for tsec0
    gtg_init:Coldboot case
    gtg_init(1):Ring bf4f6800 Peer Ring becf6800
    Uboot wdt counter value: 0
    VSD Created with major number vsd_probe = 254

    disk->start 0 cmd->start 0 nstart 0 disk name /vsmgr/vd@usb0/vda00
    HV>
    create_new_partition_table part_no 0 no_of_parts 2
    HV> INIT: version 2.78 booting
    Firmware Integrity Check is default off
    Bypassing firmware validation.
    mount: sysfs already mounted or /sys busy
    mount: according to mtab, none is already mounted on /sys
    mknod: /dev/fsl-hv: File exists
    Hostname is sw0
    INIT: Entering runlevel: 3
    FIPS-mode test application

    1. Non-Approved cryptographic operation test...
    a. Excluded algorithm (MD5)...successful

    Automatic Power-Up Self Tests...

    1. DH...successful
    2. FIPS RNG (AES_256_CTR_DRBG) selftest...successful
    3. AES-128,192,256 CBC encryption/decryption...successful
    4. RSA key generation and encryption/decryption...successful
    a. RSA 2048 with 'SHA256' testing...successful
    5. TDES-CBC encryption/decryption...successful
    6. HASH and HMAC tests...
    a. SHA-1 hash...successful
    b. SHA-256 hash...successful
    c. SHA-384 hash...successful
    d. SHA-512 hash...successful
    e. HMAC-SHA-1 hash...successful
    f. HMAC-SHA-224 hash...successful
    g. HMAC-SHA-256 hash...successful
    h. HMAC-SHA-384 hash...successful
    i. HMAC-SHA-512 hash...successful
    7. Zero-ization...Successful
    8. ECDSA ...successful
    9. ECDH ...successful
    10. TLS KDF 1.0...successful
    10a. TLS KDF 1.2...successful
    11. SSH KDF...successful
    sysmodAttach open failed: No such device or address
    sysmodAttach open failed: No such device or address
    system_parameter_init: sysModInit() failed(2)12. SNMP KDF...successful

    All tests completed with 0 errors
    GTG Peer GOS reset
    (none)
    Waiting to starting configuration management service
    Starting configuration management service
    [wmd_init]: chunk_size = 0xa00000
    [wmd_init]: WM reset
    Found 3(threshold 5) abnormal reboots within 5000 seconds window(threshold)
    KernelSpace rastrace_register
    DCM MODE:0x0
    SWBD module launch ... Fri Dec 3 03:25:10 GMT 2021
    CPLD INIT DONE
    SEEPROM Read Done!
    Cobra rev B found
    Info: panic dump has been initialized!
    Starting HASM ... Fri Dec 3 03:25:28 GMT 2021
    LAUNCH HASMD 131 0x0 0Exisitng reboot reason fsize = 5 rb=
    Global Fan Direction: Port Side EXHAUST



    Network OS (sw0)
    sw0 console login: Castor: PCIe Err handler init plat_pci_init[800]
    bhpc_irq_init: Using default device map. Size 10
    bhpc_irq_init: Pcie domain 0 err interrupt handler Installed
    Starting Dcmd ... Fri Dec 3 03:25:34 GMT 2021
    tp_register, got none fss tp handle=10000001h
    2021/12/03-03:25:35, [HSL-1012], 11, INFO, VDX6740, Interface lo is link up
    2021/12/03-03:25:35, [HSL-1012], 12, INFO, VDX6740, Interface eth0 is link up
    2021/12/03-03:25:35, [HSL-1012], 13, INFO, VDX6740, Interface eth1 is link up
    2021/12/03-03:25:35, [HASM-1004], 14, INFO, VDX6740, Processor reloaded - Reset.
    server starting
    Restoring DCM database...done

    disk->start 7665663 cmd->start 0 nstart 7665663 disk name /vsmgr/vd@usb0/vda01
    HV>
    create_new_partition_table part_no 2 no_of_parts 2
    HV> [2] restart_guest_remap: self is calling remap_restart_unc due to standby and hcall_partition_restart_ha.
    HV> [2] loading binary image from 0x79fff000 to 0x3000000
    HV> [2] Loading uImage from 0x78000000 to 0
    HV> [2] branching to guest p2-linux, 2 cpus
    HV> GTG Peer GOS reset
    waiting for server to shut down............



    Network OS (sw0)
    sw0 console login: ..admin


    .Password: ..

    .2021/12/03-03:29:47, [SEC-1206], 15, SW/0 | Active, INFO, sw0, Login information: User [admin] Last Successful Login Time : Fri Dec 3 03:18:22 2021
    .
    ...Error: Network OS is not ready. Please login later.
    .2021/12/03-03:29:51, [SEC-3022], 16, SW/0 | Active, INFO, sw0, Event: logout, Status: success, Info: Successful logout by user [admin].



    Network OS (sw0)
    sw0 console login: ...............


    Original Message:
    Sent: 12-02-2021 22:51
    From: Russ
    Subject: Confirm how to configure logical-chassis mode

    Thanks for the info Truyen. 

    Something's gone south with the firmware downgrade, I'm now in a bootloop on the switches. I'm getting an output of the boot process ATM to post here.
    Original Message:
    Sent: 11-29-2021 22:05
    From: Truyen Phan
    Subject: Confirm how to configure logical-chassis mode

    In 7.0.x, the command is the same as the one you posted in your first post: 

    vcs vcsid 1 rbridge-id 2 logical-chassis enable 
    Original Message:
    Sent: 11-29-2021 18:48
    From: Russ
    Subject: Confirm how to configure logical-chassis mode

    Thanks again, for reference what was the command to configure logical-chassis mode?
    Original Message:
    Sent: 11-29-2021 01:12
    From: Truyen Phan
    Subject: Confirm how to configure logical-chassis mode

    You will need to downgrade to 7.0.x, then set the vcs mode to logical chassis, then upgrade.
    Original Message:
    Sent: 11-29-2021 01:03
    From: Russ
    Subject: Confirm how to configure logical-chassis mode

    Hi thanks for you reply. When I was checking the status after applying the VCSID and RB ID the output indicated that the switch was in VCS Mode : Fabric Cluster and not logical-chassis. 
    Original Message:
    Sent: 11-29-2021 00:55
    From: Truyen Phan
    Subject: Confirm how to configure logical-chassis mode

    Hi Russ,

    Starting NOS 7.1.x and higher, the only valid VCS mode is logical chassis which is enabled by default, so there's no need to configure logical-chassis enable anymoreYou just need to set the VCS ID and RB ID.
    Original Message:
    Sent: 11-28-2021 21:36
    From: Russ
    Subject: Confirm how to configure logical-chassis mode

    Hi I'd like to confirm the correct command to configure a VDX6740 firmware 7.2.0c.
     
    I read in some older doco switch# vcs vcsid 1 rbridge-id 2 logical-chassis enable but this is not available and I can't recall the correct syntax and mode to execute this. 

    Thank you.