22541 12phwov inline large

ExtremeSwitching (EOS)

Conversations

Recent Conversations
Conversations 1 - 15 of 619
Photo of Frank Richter
7100 Series, VSB / additional Link
Hi, I have 2 7100K Switches (8.63.02.0004) with VSB 1 x 40 Gbps and 1x 10 Gbps. Now I want to connect additional Link 40Gbps and 10 Gbps ...
  • 1 me too
  • 0 replies
  • Question
Photo of Byron Morales
Create a script that will automatically toggle POE on a port if an AP goes down
One of the first things we try to do if an AP goes down in the controller is to find where that AP is and toggle POE. It would be neat t...
  • 2 me toos
  • 1 reply
  • Question
  • Answered
Photo of Jake Koch
EXOS MLAG and bonded S8s
Hello Extreme Hub, I have a questions regarding EXOS MLAG and bonded S8s 1st here is the scenario: I have a customer with bonded S8s t...
  • 1 me too
  • 6 replies
  • Question
  • Answered
Photo of Visconti
"Node alias interface summary" not run in B5 series
Do anyone say me why the flexview "Node alias interface summary" not run in B5 series ??
  • 1 me too
  • 1 reply
  • Problem
  • Solved
Photo of Visconti
how to restart a port of B5 series switch (power down and restart)
I need to reset (remove voltage and restart) one particular port  whitch is connected a network clock. This clock is in crash and I canno...
  • 2 me toos
  • 5 replies
  • Question
  • Answered
Photo of theoadon
Replacing a Cisco 3845 router and Cisco 3560 switch with extreme products
HI There,We asked from a customer to replace his network equipment.Now the customer's site is using a Cisco 3845 router and Cisco Catalys...
  • 1 me too
  • 9 replies
  • Question
  • Answered
Photo of Pawel Eljasz
vdx-6740 ports respond differently to the same cable(transceiver)
hi everyone I have SFP+ cables which seems to work fine but on one(maybe more?) port(Te 2/0/27) I see "unqualified transceiver" and port...
  • 2 me toos
  • 3 replies
  • Problem
Photo of Enrico Celegon
Banner
I would like to configure Extreme 200 series, x460 and x670 to receive cli-banner, MOTD, failed auth, user welcome, ecc... directly from ...
  • 1 me too
  • 0 replies
  • Idea
Photo of Jan Steinbach
[S-Series] [VSB] HAU Incomptible with 08.11.04.0006
Hello Community,I have an Chassis based S-Series configured as an VSB, running EOS 08.11.04.0006.Primary due to an SNMP problem (Switch d...
  • 2 me toos
  • 1 reply
  • Problem
Photo of Adm Infra
G3 firmware 06.61.18 download
I can see the release notes, but not the actual software, invisible for download.
  • 1 me too
  • 1 reply
  • Question
Photo of Prasanna A
How to Block(Selfish Net, Net cut) software attack users?
How to Block(Selfish Net, Net cut) software attack users? Lot of users using like selfish net, netcut application block all users bandwi...
  • 1 me too
  • 1 reply
  • Problem
Photo of Alok Shukla
Want to configure etherchannel over point to point link of different ISP
Want to configure LAG over point to point link of different ISP? In below figure, we want to configure Fa0/1 and Fa0/2 LAG and both port ...
  • 1 me too
  • 3 replies
  • Question
Photo of ar
Design Question: should I use MGMT port or better not?
Hi all, we have many switches (EOS and EXOS) and I would like to know if my design is OK or how to make it better. We have switches in o...
  • 1 me too
  • 2 replies
  • Question
Photo of James A
G3 firmware 06.61.18 download
Is it possible to download G3 firmware from the new portal? I can see the release notes, but not the actual software.
  • 4 me toos
  • 1 reply
  • Question
  • Answered
Photo of Drew C.
RESOLVED: Community Login Issues with Portal Accounts
Hi everyone, I've been informed of a potential issue affecting login to The Hub when using Extreme Portal account credentials. Some users...
  • 1 me too
  • 3 replies
  • Announcement