21775 11xm7p6 inline large

Network Architecture & Design

Conversations

Recent Conversations
Conversations 1 - 15 of 301
Photo of Nathan Derichsweiler
RFS4000 act as router to cable modem?
I am having difficultly getting an RFS4000 to connect to my ISP through my cable modem. I am new to AP controllers. I would assume(correc...
  • 1 me too
  • 4 replies
  • Question
Photo of Alok Shukla
How To define QOS on Fastethernet port of different VLAN?
We have X440 switch as we take MPLS connection of 100mbps for connecting another site. We want to pass two VLAN on that port and prioriti...
  • 1 me too
  • 2 replies
  • Question
Photo of Alok Shukla
Ports connected to single MLAG id?
We have Core switches(X-670) that connected to X440(48 ports) stacks of 4 switches. Is this supported "48 ports * 4 switches =192 ports" ...
  • 1 me too
  • 2 replies
  • Question
Photo of Technolust
stencils 200 Switches
200 Series Stencils for Visio can't map ports lines go to switch
  • 1 me too
  • 0 replies
  • Problem
Photo of Alok Shukla
Network Health Check List
Hey, can anyone have a network health checklist? We have no monitoring tool.
  • 1 me too
  • 1 reply
  • Question
Photo of nola saint
Home Lab for extreme networking
Home Lab for Extreme Networking. Would like to setup a lab to learn about Extreme networking. What switches are good to buy off ebay for ...
  • 1 me too
  • 7 replies
  • Question
  • Answered
Photo of Drew C.
FN-2018-421, ERS Flash Failure due to Excessive Writes
Extreme Networks has recently discovered an issue on certain versions of ERS 4800, ERS 4900, and ERS 5900 software which can result in an...
  • 2 me toos
  • 0 replies
  • Article
Photo of Marc Daley
SLPP design ERS8k to VSP7k
I'm currently looking at updating a customer deployment of SLPP within a datacentre. I have looked at the following design docs -  Switc...
  • 1 me too
  • 2 replies
  • Problem
  • In Progress
Photo of Brandon Clay
Official statement on VPNFilter
Hello everyone, Extreme Networks has published an official statement regarding the VPNFilter malware. You can find it here: https://extr...
  • 3 me toos
  • 0 replies
  • Article
Photo of Leonardo Peixoto
Phased migration from ExtremeWireless V9 to V10
Hi Guys, I'm working on a LAB environment to find the best (or less painful) path to migrate a customer installed base to V10. This cus...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Soon Lin Ewe
Anyone with experience in ring topology configuration by Using the dual-ISW Switches.
Hi Team,I am looking for any experts that has done a dual ring configuration L2, with using the ISW switches. The customer is looking for...
  • 1 me too
  • 0 replies
  • Question
Photo of Martin Flammia
Extreme Control behind a firewall
Hi, Currently looking into running a NAC behind a firewall and looking into this GTAC post: https://gtacknowledge.extremenetworks.com/a...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Bill Bixby
Core Routing VLAN
Best practices for layer 3 network design and routing traffic
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Walt Witkowski
Comments welcomed on multicast configuration
Running two S4 cores, each with a VRRP instance to 25 individual closet switch stacks.  I am enabling IGMP on each network in each core t...
  • 1 me too
  • 0 replies
  • Question
Photo of Martin Flammia
ZTP+ Switch not showing up in EMC
Hi, In the process of configuring ZTP+.  The switch has been set to 'unconfigure switch all' and seems to be obtaining an IP address. ...
  • 1 me too
  • 6 replies
  • Question
  • Answered