18920 1g8z1s6 inline large

Switching & Routing

Conversations

Recent Conversations
Conversations 1 - 15 of 2112
Photo of Bill Bixby
Core Routing VLAN
Best practices for layer 3 network design and routing traffic
  • 1 me too
  • 3 replies
  • Question
Photo of ar
Question about VLAN Egress Priority at Switches (G3G and C5K, stativc vers. assign by auth))
Hello, I have the following problem: I have a managed 4 Port-Noname-Switch attached at a switch G3G124-24 at port ge.1.4. The managed 4-P...
  • 1 me too
  • 2 replies
  • Question
Photo of Rick Elliott
Dual Mode and voice vlan not working properly on brocade switch
Hello, We had cisco callmanager phone system. Using Brocade ICX 7450 switch with following config vlan 10 by porttagged ethe 1/1/1 to 1/1...
  • 1 me too
  • 1 reply
  • Problem
Photo of M.Nees
VOSS: command history
With EOS or EXOS if often use "history" command so see which commands are entered in a short summary. In current VOSS (V6.1.0 or V7.0) i...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Imre Kordás
ERS 3510GT-PWR mounting dimensons
Hello everyone! I would like to know the dimensions of the rack mounting holes on the ERS 3510GT-PWR ethernet switch for an own mounting...
  • 1 me too
  • 0 replies
  • Question
Photo of Brian Holmes
4500 802.1x EAP behavior
We have a 4500 switch running SW:v5.11.1.101 When we connect an 802.1x client, the switch is sending a new authentication request every ...
  • 1 me too
  • 0 replies
  • Problem
Photo of Leonardo Peixoto
XMC 8.1 Policy Manager shows A2-Series as UNSUPPORTED
Greetings Guys, Here we go again with legacy gear... But they are dying hard, because *almost* nothing can break it, they got forgotten ...
  • 1 me too
  • 4 replies
  • Problem
Photo of Кирилл Кучеров
Memory leak by process CFGMGR after save configuration
We have such problem. Always after saving configuration, we have found the memory leak, about 2MB from process CFGMGR. Because of this we...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Mike Assel
igmp snooping & vlan routing Extreme 220
The admin guide for the Extreme 220 says "If an interface has IGMP Snooping enabled and you enable this interface for routing or enlist i...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Rowan Sakul
Change Summit X670 / X670V air flow direction
Hi, I wanted to know whether we can change the air flow direction of the original Summit X670 / X670V (G1) series of switches by replacin...
  • 2 me toos
  • 3 replies
  • Question
  • Answered
Photo of Erol Asim
Fabric Extend - cannot get adjacency over IP Tunnel
Unsuccessfully cannot get an adjacency in GNS3 VOSS 7.0 using Fabric Extend over IP Tunnel using loopbacks. Can anyone advise where I’m g...
  • 1 me too
  • 9 replies
  • Problem
  • In Progress
Photo of Yves Haslimann
Show Last interface status change 200-series
Hello Is there a command on the 200-series Extreme switches to see the last interface change?For example, Last up: 3 daysLast down: 2...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of kjstech
Brocade Ti24x default-gateway will not work if set to VRRP address on EXOS core
Hello, We have two X690 core switches in our network doing layer 3, and they run VRRP between them.  The VRRP address is the default gate...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Biggtimber
Routing the Management address over an LACP lag
I am banging my head against the table trying to get my management IP routing across a LACP lag from my 220  a Dell F10 switch.  In my ea...
  • 2 me toos
  • 1 reply
  • Problem
  • Solved
Photo of Kyle Chislett
Need to migrate a VDX6740T-1G DC ToR switch to another rack. Safe to power off/power on without disruption?
Need to migrate a VDX6740T-1G DC ToR switch to another rack. Is it safe for me to power it down, move and power it up in the new rack wit...
  • 1 me too
  • 2 replies
  • Question
  • Answered