18920 1g8z1s6 inline large

Switching & Routing

Conversations

Recent Conversations
Conversations 1 - 15 of 2191
Photo of Andre Jordaan
vsp 7200 monitor-by-isid
Running version 6.1.x at the moment on 8 x VSP 7200.In a Nutshell:Im testing an IDS solution and configured a monitor-by-isid (with QoS =...
  • 2 me toos
  • 0 replies
  • Question
Photo of Thavamani Shanmugam
How to block IP Scanner Software using EXOS Switch...
Hello, We have around 40 numbers of x440-24P EXOS based Switches in our campus. Some of the users connected in these Switches using d...
  • 1 me too
  • 0 replies
  • Question
Photo of Roberto Alvarez
Extreme 220-Series support SNMP Set from Netsight?
We have install a new stack with two 220-48t-10GE4 and connect them to our netsight (6.2)With other equipment we can edit and modify the ...
  • 1 me too
  • 0 replies
  • Question
Photo of theoadon
Does promiscuous mode on VM adapter needed for VX9000
HI there,We are migrating from RFS6000 to VX9000, an existing WLAN with APs 6521,7522 and 6562.For adoption all these APs , does promiscu...
  • 1 me too
  • 3 replies
  • Question
Photo of Joseph Crist
avaya switch password reset stack
I have a couple of Avaya 5500 series switches. I can no longer access one of them because I have forgotten the password. I heard it is po...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Jake Koch
EXOS MLAG and bonded S8s
Hello Extreme Hub, I have a questions regarding EXOS MLAG and bonded S8s 1st here is the scenario: I have a customer with bonded S8s t...
  • 1 me too
  • 6 replies
  • Question
  • Answered
Photo of Timothy Corcoran
Displayed Routes in "sh ipr" different than expected based on LSDB
Issue:Why does sh IPR treat destination networks differently even though at first glance they should be treated the same?   Refer...
  • 1 me too
  • 2 replies
  • Question
Photo of aloeffle
Where to download legacy firmware (EOS)?
Dear all. On and off I need specific legacy firmware versions for Enterasys devices running EOS. C-Series, B-Series, etc. Since we have ...
  • 4 me toos
  • 9 replies
  • Question
  • Answered
Photo of Peter
VLAN Mirror on EOS 7100 Switch?
Hello, is it possible to configure a VLAN mirror on a EOS 7100 (VSB) switch? A port mirror don't help, because I need to analyse traffic...
  • 1 me too
  • 1 reply
  • Question
Photo of Thyago C. Rodrigues
Help with an MPLS/OSPF architecture
Hi dears,I would like a help with the architecture displayed below. Please feel free to make any comment.Network descriptions and require...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Drew C.
Community Platform Issues
Hello everyone, As you have surely noticed, our community has been impacted by an issue our platform provider has been working on since y...
  • 1 me too
  • 3 replies
  • Announcement
Photo of Thyago C. Rodrigues
Help with an MPLS architecture
MPLS with OSPF or MPLS with iBGP?
  • 1 me too
  • 2 replies
  • Question
  • Doesn't Need an Answer
Photo of Frank
Access-list (rate limiting) and port shares / LAG/LACP
On a Summit-X460, Exos 15/16.x, I have a LAG I also have ingress ACLs (for rate limiting) and egress rate-limits. Do I apply those to al...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Rowan Sakul
Unable to use WinSCP to connect to XOS Switches anymore
Anyone else having trouble using WinSCP to connect to XOS switches?Unfortunately I haven't had to connect for some time, so I cant pinpoi...
  • 2 me toos
  • 1 reply
  • Problem
Photo of Jean-Albert Vescovo
Is it possible to get multiple is-is adjacencies on a same port with VOSS7 on VSP 7200 series switches ?
This question because we use an operator's L2 VPN tunnels to interconnect our VSP on different remote sites. Instead of using a different...
  • 2 me toos
  • 4 replies
  • Question
  • Answered