18920 1g8z1s6 inline large

Switching & Routing

Conversations

Conversations 1 - 15 of 462
Photo of Brandon Cuellar
Extreme switches 200 series SFP uplinks are not working
Customer has a 220 series 12 port and 48 port and is trying to connect the 2 via SFP ports on 1/0/13 on the 12, and 1/0/49 on the 48, but...
  • 1 me too
  • 6 replies
  • Problem
  • In Progress
Photo of Brian Holmes
4500 802.1x EAP behavior
We have a 4500 switch running SW:v5.11.1.101 When we connect an 802.1x client, the switch is sending a new authentication request every ...
  • 1 me too
  • 1 reply
  • Problem
Photo of Resolut1on
TTL expired in transit!
Hi Friends,  Good day.  I have problem with Inter-Vlan. Our goal is PC1 must communicate to PC2 with different VLANs. same as PC2 to P...
  • 1 me too
  • 6 replies
  • Problem
Photo of Danial Jalil
Can flow-redirect be used on layer 2 ? if yes, Syntax please
I want to redirect flows based on port numbers. Is there a way to achieve that?
  • 2 me toos
  • 2 replies
  • Problem
  • Not a Problem
Photo of Bruno
Lag X460G2 CCR1009
Hi, im having a issue while tring to bond 2 ports between a x460-g2 and a mikrotik ccr1009. My TX traffic get balanced but there is no wa...
  • 1 me too
  • 6 replies
  • Problem
  • Solved
Photo of Leonardo Peixoto
XMC 8.1 Policy Manager shows A2-Series as UNSUPPORTED
Greetings Guys, Here we go again with legacy gear... But they are dying hard, because *almost* nothing can break it, they got forgotten ...
  • 1 me too
  • 5 replies
  • Problem
Photo of Rick Elliott
Dual Mode and voice vlan not working properly on brocade switch
Hello, We had cisco callmanager phone system. Using Brocade ICX 7450 switch with following config vlan 10 by porttagged ethe 1/1/1 to 1/1...
  • 1 me too
  • 1 reply
  • Problem
  • Solved
Photo of Erol Asim
Fabric Extend - cannot get adjacency over IP Tunnel
Unsuccessfully cannot get an adjacency in GNS3 VOSS 7.0 using Fabric Extend over IP Tunnel using loopbacks. Can anyone advise where I’m g...
  • 1 me too
  • 9 replies
  • Problem
  • In Progress
Photo of Biggtimber
Routing the Management address over an LACP lag
I am banging my head against the table trying to get my management IP routing across a LACP lag from my 220  a Dell F10 switch.  In my ea...
  • 2 me toos
  • 1 reply
  • Problem
  • Solved
Photo of meconomou
Connect Extreme Summit Stack to Cisco FTD2110 HA Firewall Pair via L2
Tried doing a cutover last night to new the Cisco FTD2110 HA firewall pair ether channeled to an EXOS stack. Channel came up and vlan int...
  • 1 me too
  • 2 replies
  • Problem
  • Not a Problem
Photo of Ian Broadway
Rx CRC and Rx Jabber
Hello, We're experiencing infrequent CRC/Jabber errors on a particular interface between 2 670v-48x switches.  Switches are running code...
  • 1 me too
  • 4 replies
  • Problem
  • Not a Problem
Photo of Michael Goodliffe
Extreme stack no management access
I need help with configuring external access to my Extreme stack. The stack consists of X450e-48p (master), X650-24x (secondary). I need...
  • 1 me too
  • 11 replies
  • Problem
  • Solved
Photo of Martin Flammia
OSPF Stub between EOS and EXOS not updating routing table
Hi, Have a OSPF issue that I must be missing something obvious. Basically I have some EXOS devices activing as the core OSPF backbone ar...
  • 1 me too
  • 1 reply
  • Problem
  • Solved
Photo of Lizbeth
Error bcmStrat[11.tMiiDbnc]setLinkMode
Hello, My port don ́t work and the switch show the following message: <163>May 14 12:59:20 XX.XX.XX.XX bcmStrat[11.tMiiDbnc]MacDrainTime...
  • 1 me too
  • 1 reply
  • Problem
  • Solved
Photo of EtherMAN
Can't get a link between a 870 QSFP28 sr4 100 gig and a Brocade MLXe 100 gig using CFP2-TO-QSFP28-Module
We are in the process of bring up new MLXe routers with 2 port CFP2 100 gig cards.  We are connecting these to 870 100 gig QSFP28 interfa...
  • 1 me too
  • 0 replies
  • Problem