18925 5z5uax inline large

ExtremeSwitching (EXOS)

Conversations

Recent Conversations
Conversations 1 - 15 of 3731
Photo of Rahman Duran
Does X460-G2 need special config for snmp access?
Hi,We have a new building with one X460-G2 as core switch/router and many X440-G2 as edge switches. We started configuring and adding the...
  • 1 me too
  • 1 reply
  • Problem
  • Solved
Photo of Resolut1on
NMS license installation.
Hi Extreme Networks, I already installed the nms in our server. Can I install it again and use the license key in another 1 server ...
  • 2 me toos
  • 2 replies
  • Question
  • Answered
Photo of harish.sadineni
How To Configure EXTREME -- X 440-G-48t-10GE4 Switch Stack using MULTI MODE FIBER OPTIC PATCH CORD
HI Frnds I have One Problem I want to Configure Stacking with Two  48 Switches of Model X 440-G-48t-10GE4 Switches. I dont Have Stacking ...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Visconti
learned mac address refer to group
I have created a DEVICE GROUP with ITS INTERNAL only two port/pc so I STARTED the flexview "learned mac addresses" to know if the 2 pc ar...
  • 1 me too
  • 0 replies
  • Question
Photo of Harkanwaljeet Singh
EXOS SNMP access-profiles
Hi Community, There are many articles on the SNMP access-profiles; I have gone through few of them but could not find the answer to my sp...
  • 1 me too
  • 1 reply
  • Question
Photo of Visconti
Show IP address of specific port
I have finally use netsight console v8 after using GUI web version.Can I create a flexview that can show me the IP address of all port of...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of nayzaw win
Looking for clarification on the enable iproute sharing command
Dear all, I used this command enable iproute sharing and then in routing table show tow routes but traffic one path so why ? Please tell me.
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Jake Koch
EXOS MLAG and bonded S8s
Hello Extreme Hub, I have a questions regarding EXOS MLAG and bonded S8s 1st here is the scenario: I have a customer with bonded S8s t...
  • 1 me too
  • 6 replies
  • Question
  • Answered
Photo of Steve Ballantyne
Lousy, stupid, stubborn old radiology devices (and the Summit stack that hates them)
Howdy folks,I am trying to finish up a job replacing some very old Cisco 3750's with a new stack of Extreme Summit 450-G2 switches runnin...
  • 1 me too
  • 3 replies
  • Problem
  • In Progress
Photo of Epafras Schaden
Extreme X670-G2 - IP Fabric with BGP evpn and xvlan
Hello, Can anyone share some documentation or an example of configuration to Extreme EXOS (X670-G2) about an IP Fabric configuration usi...
  • 1 me too
  • 0 replies
  • Question
Photo of Bryan Hernadez
Hello ! query ... an extrem SW supports more than one vlan in a port? Or should we eliminate the vlan to add another? Regards!
Hello ! query ... an extrem SW supports more than one vlan in a port? Or should we eliminate the vlan to add another? Regards!
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Rick Sanson
Moving VLAN address definitions from Cisco To VSP - Retire Cisco - Error: Mulitnetting Not Supported
I am moving from Cisco to Extreme (VSP/ERS). I have a layer 2 connection between the Cisco core and the VPS "core". I have 5 VLANs (defau...
  • 1 me too
  • 0 replies
  • Problem
Photo of David Coglianese
22.6.1.4 Auto Stacking
Looking for other people experiences and reporting my test results below.First tests who that auto stacking is pretty cool and works wel...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Maple Wang
Can't set factory default or upgrade for summit x450a-48t
Hi, we are using summit x450a-48t with exos 15.3.2.11, recently, we want to reinstall or set factory default to it, but it didn't work. ...
  • 1 me too
  • 7 replies
  • Problem
  • Solved
Photo of Randy
I am using the 8806 MSM-48c and can I use the 8900-10G24x-c I / O Module?
I am using the 8806 MSM-48c and can I use the 8900-10G24x-c I / O Module?
  • 1 me too
  • 1 reply
  • Question
  • Answered