Conversations

Conversations 1 - 20 of 33
Photo of Alok Shukla
Can we enable stack on already been configured X440-g2 switches or does we have required default setting for enabling stack?
Can we enable stack on already been configured X440-g2 switches or does we have required default setting for enabling stack?
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Alok Shukla
ACL applying over VLAN
We have three VLAN's all are inter-VLAN routing. VLAN-1= 10.3.1.0 VLAN-2= 10.3.2.0 VLAN-3= 10.3.5.0 My boss wants to VLAN-2 and 3 should ...
  • 1 me too
  • 2 replies
  • Problem
  • Solved
Photo of Alok Shukla
ACL for applying over VLAN
We have 4 VLAN over Core Switch (MLAG configured) VLAN 1: 10.3.1.0 VLAN 2: 10.3.2.0 VLAN 3: 10.3.3.0 VLAN 4: 10.3.4.0 we don't want VLAN...
  • 2 me toos
  • 3 replies
  • Question
  • Answered
Photo of Alok Shukla
MLAG whic should we have to configure STP?
  I had created MLAG on core switches, Now on this topology diagram can you clarify me in which switch we have to apply STP ?
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Alok Shukla
Best designing of a Network
We have total 27 X440-G2-24p switches but at our core, we are using Cisco 4500X switches in an active-active state using VSS based config...
  • 2 me toos
  • 2 replies
  • Question
  • Answered
Photo of Alok Shukla
Creating Stack of connected cascade switches?
we have X440-G2 switches in our production environment and these switches are connected in a cascade manner, Does any Pre-configured swit...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Alok Shukla
Could we create Stacking over two switches?
Could we create Stacking over two switches?
  • 2 me toos
  • 6 replies
  • Question
  • Answered
Photo of Alok Shukla
MLAG is good or bad in this topology diagram?
We have Core A and Core B Cisco switch's both are working in active-active and deployed in Building A, and in our environment, all access...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Alok Shukla
Could X440-G2 is supported MLAG Peer ?
Could X440-G2 is supported MLAG Peer ? I Don't want to run VRRP i just want to pass uplink L2 traffic to core level switches for other ve...
  • 1 me too
  • 1 reply
  • Problem
  • Not a Problem
Photo of Alok Shukla
Cisco 4500 have VSS solution and Extreme have X690 mlag peer solution which one best?
Cisco 4500 have VSS solution and Extreme have X690 mlag peer solution which one best?  Give advantages and disadvantages
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Alok Shukla
X440-G2 intervlan routing
Could X440-G2 series supports Inter-VLAN routing? is this manageable switch?
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Alok Shukla
Does X440 G2 switch support MLAG at distribution level?
Does X440 G2 switch support MLAG at distribution level?  Is it possible X440 G2 at the distribution level and also X400 G2 at access leve...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Alok Shukla
Exxtreme Switch IOS upgradation
I am having extreme switch summitX-16.1.1.4.x  can we directly upgrade to Extreme summitX-21.1? During upgradation how much downtime is ...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Alok Shukla
Warning error display
13:45:11.96 <Warn:IPMC.Warning> Our own packet received. Mac address of the received packet is [0:4:96:35:75:d4],there could be physical ...
  • 1 me too
  • 2 replies
  • Problem
  • Not a Problem
Photo of Alok Shukla
Backup of switch x620-16x
During taking backup of switch configuration, the ACL configuration is by default downloaded or we can manually be downloaded?????
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Alok Shukla
DHCP clients get IP without configuring DHCP relay on switch
In our network environment, we are using x620 and x440 and all users getting IP without configuring DHCP relay agent on the switch. how i...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Alok Shukla
How do upgrade SFP 1gb link to 10 gig onx440
How do upgrade SFP 1gb link to 10 gig on x440 switch?
  • 1 me too
  • 7 replies
  • Question
  • Answered
Photo of Alok Shukla
MLAG issue
we want to createing MLAG between 2 switches X620. During MLAG creation does IP of all VLAN between 2 switches be same using or same subn...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Alok Shukla
How do configure trust DHCP snooping on ports?
How do configure trust DHCP snooping on ports?
  • 2 me toos
  • 1 reply
  • Question
  • Answered
Photo of Alok Shukla
VRRP priority
I have configured MLAG(X670) on two switch and want to configure VRRP active-active can we use same priority level on both switches?
  • 1 me too
  • 4 replies
  • Problem
  • Solved