Conversations

Conversations 1 - 20 of 147
Photo of Andre Brits Kannemeyer
S Series Chassis with S180 Fabrics blades and 150 IO blades
Hi have two S8 Chassis with S180 fabric blades and S150 IO blades. For the IO blades to operate we have to change the "Chassis Compatibil...
  • 1 me too
  • 1 reply
  • Question
Photo of Andre Brits Kannemeyer
XOS Fabric Attached
Hi Community I recently started playing with the Extreme Fabric Connect (Old Avaya Fabric) and some Fabric Attached XOS switches and 39x...
  • 1 me too
  • 11 replies
  • Question
Photo of Ilya Semenov
What is the most appropriate network design for this topology?
Hello, everybody! I have a task to totally redesign a huge network which consists of about 150 switches (old enterprise CISCOs). Everyth...
  • 1 me too
  • 8 replies
  • Question
  • Answered
Photo of Claudio D'Ascenzo
Configure OSPF on X670-G2
Hi all I have to configure OSPF and VRRP in an hospital networks, we have two X670-G2 with Core license. My requirement is have high avai...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Andre Brits Kannemeyer
S Series BDF Supported sessions
Hi Community I have a question regarding BFD on the Series Switch (180 Fabric Blades Installed) I am utilizing BFD on the S Series Switc...
  • Andre Brits Kannemeyer, 2 months ago

  • 1 me too
  • 0 replies
  • Question
Photo of Robert S.
topology configuration for multiple site wireless service
Hi together! We are in the process of migrating a C25 Controller to V2110. This is the perfect time to review our configuration. ;) I n...
  • 2 me toos
  • 3 replies
  • Question
  • Answered
Photo of Andre Brits Kannemeyer
XMC Device Type Visibility
Hi Community. With the Version 10 of the Identify wireless firmware, it identifies device types, without the need for NAC. Can XMC repor...
  • 2 me toos
  • 1 reply
  • Question
  • Answered
Photo of Alok Shukla
ACL applying over VLAN
We have three VLAN's all are inter-VLAN routing. VLAN-1= 10.3.1.0 VLAN-2= 10.3.2.0 VLAN-3= 10.3.5.0 My boss wants to VLAN-2 and 3 should ...
  • 1 me too
  • 2 replies
  • Problem
  • Solved
Photo of Andre Brits Kannemeyer
x440 G2 route sharing
Hi I am looking at ECMP on a x440 G2 switch. The x440 is connected to two seperate routers and I would like to load balance traffic acros...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Andre Brits Kannemeyer
BDF between Summit Edge switch and S Series Core
Hi community I am connecting a x440-g2 two to S-Series VSF bonded chassis. The x440 will be configured with two static routes and run ...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Alok Shukla
X440-G2 intervlan routing
Could X440-G2 series supports Inter-VLAN routing? is this manageable switch?
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Andre Brits Kannemeyer
What does the S series switches do with Multicast traffic across a VXLAN Tunnel
Hi Community I am currently using VXLAN tunnels for "Data Center interconnection". By default Proxy ARP is enbaled to limit the broadcas...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Andre Brits Kannemeyer
VXLan Support on x460-G2
Hi Community I thought I would drop the question here before asking an official question to GTAC. Why do we not have VXLan support on t...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Andre Brits Kannemeyer
Legacy Securestack B2G switches hang management
Hi Community I thought I will ask the question here as the problem switches that I have is very old. A client of ours have a few hundred...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Andre Brits Kannemeyer
40Gbe FAN out DAC Cable with S Series
Hi community We are looking at using the 40Gbe fanout cable with s series 40Gbe blade. The Datasheet for the 40Gbe fanout cable only lis...
  • 2 me toos
  • 1 reply
  • Question
  • Answered
Photo of Andre Brits Kannemeyer
Extreme Cloud with External Captive Portal authentication
Hi Community We have a client that is looking at deploying numerous AP's for a free wifi service. The AP's will be dispersed across a to...
  • 1 me too
  • 1 reply
  • Idea
  • Under Consideration
Photo of Andre Brits Kannemeyer
3965i/e PSE Out (LAN2)
Hi Community Has anyone played with the POE out port on the 3965 series AP's?? I do not seem to be getting any power out on the send por...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Andre Brits Kannemeyer
Gbic support on Legacy Enterasys and new Summit switches
Hi Community Perhaps someone can point me in the correct direction. We have a client that have over 500 of the Secure Stack (B5's, C5's ...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Andre Brits Kannemeyer
Extreme Management - Connect
Hi Community Recently I saw some posts referring to the "Distributed IPS" module in "one Fabric Connect". Without this post I would neve...
  • Andre Brits Kannemeyer, 4 months ago

  • 3 me toos
  • 0 replies
  • Idea
  • Under Consideration
Photo of Ilya Semenov
Redundancy between two NAC instances
Hello, everybody, how could I set redundancy between two NAC instances? I have set up MAC and 802.1x auth on my switches, but it works ...
  • 1 me too
  • 8 replies
  • Question
  • Answered