Conversations

Conversations 1 - 20 of 33
Photo of Gerald Nuque
Devices Shows SNMP Contact Lost (Down) but able to Manage and Ping in XMC
Hi, We've installed a trial version of XMC and added 12 units 210-24p switches. The ten switches are working smoothly while two switches...
  • 2 me toos
  • 3 replies
  • Problem
  • Solved
Photo of muthu naganathan
802.1x authentication
Hi Team, I need to configure the 802.1X authentication in Summit X440 -24p-10g switch. I have NPS server in our environment . S...
  • 1 me too
  • 9 replies
  • Question
  • Answered
Photo of Rich
ACL counters not showing
Hi,  I have an ACL defined to manage general access between subnets across switches, and as part of that some rules have counters assigne...
  • 1 me too
  • 10 replies
  • Problem
  • Not a Problem
Photo of Helpme
histogram of packet statistics OID value
I want use PRTG Get my Extremes XOS switchs histogram of packet statistics but i search MIB file can't found this value, who can tole me ...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Mario Cruz Torres
Initial Configuration BD8810
Hello Expert, Im start configuring my first BD8810: First I want to upgrade the node, but for that I configure a vlan with an IP Addre...
  • 1 me too
  • 14 replies
  • Question
  • Answered
Photo of Resolut1on
(pending-AAA) login:
I pulled out a switch from stacking it is a STANBY mode. But now this is the scenario. (pending-AAA) login: Warning: the stack has n...
  • 1 me too
  • 4 replies
  • Problem
  • Solved
Photo of Steven Marriott
Stack switch fails and brings the whole LAN down
i have  x440-48T Switch stacks in my Local LAN, over the last 6 months the LAN has been brought to a standstill because of a failure on a...
  • 1 me too
  • 3 replies
  • Problem
  • Not a Problem
Photo of Peter Millard
SSL module for x450a24t in home lab environment
Hi there, i have an x450a24t in a home lab environment, and as such have no warranty or support on this device.I am looking to get HTTPS ...
  • 1 me too
  • 8 replies
  • Question
  • Doesn't Need an Answer
Photo of Юрий Сулак
oid dhcp
I need oid (or tree) to see dhcp leases from my extreme x450a-24x. And also need how to configure dhcp server(static mac+ip) via snmp. Th...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Peter Millard
Chalet equivalent
I have an x450a24t running the latest firmware, thus comes with the screenplay Web interface. Is there anyway to upgrade the firmware ...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Fagner
how to lock a static ip in interface port in the switch EXOS 15.7?
  • 1 me too
  • 6 replies
  • Question
  • Answered
Photo of Yusuf Kabbara
how to find where the topology changes are happening?
I have about 130 switches in 8 rings topology, all connected to one core switch. looking to the "Number of Topology Changes" I am finding...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Benzion Nussbaum
initial setup x250e
I just got hold of a few extreme x250e and I would like to use them to power a camera system that I have ( I am a cisco guy but just got ...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Claudio Minnetti
Summit X670V-48t - Switchport stuck in ready status
Product Model: Summit X670V-48t-FB-AC Software Version: 16.1.3.6 Ethernet Switchport 1:7 remain in ready status even if a device is conn...
  • 1 me too
  • 6 replies
  • Question
  • Answered
Photo of Arjumand Qazi
Do we have a tool from extreme for network designing something similar to visio?
online designing tool from extreme networks
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of waqas
Frequent alarm on switch
Hi Experts, Frequently getting this alarm on switch please advise.   6-4-2017 10 :55 45 [ 10.170.13...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Rod Robertson
Control ELRP ingress and egress
Can you configure for ELRP what are the ingress ports and what are the egress ports . I already understand how we need to configure this ...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of greg rayan
core switch configure stp
hello  i have a core swich extreme summit x450 and I would like to know how to configure the spanning tree I believe that the priority mu...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Andre Brits Kannemeyer
C5210 Wireless Controller SNMP v3 User Access
Hi Community I have a quick question regarding SNMP v3 Users on a wireless controller. On the switches I can create SNMPv3 group with r...
  • 2 me toos
  • 3 replies
  • Question
  • Answered
Photo of Craig William Westbrook
RSTP Ports
Are the ports that I need to add to the RSTP domain, the ports that are connected from switch to switch or all ports?
  • 1 me too
  • 2 replies
  • Question
  • Answered