Conversations

Conversations 1 - 20 of 50
Photo of Ronald Dvorak
ECA - how to add a switch
How could I tell my 220 switch to connect to my ECA. I'm running latest software so that is OK but I can't find how I'd tell the switch ...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Knut
Netsight - Device temperature
Hi, Does anybody know if it's possible to show the device temperature in celsius when generating a report in Extreme Management? When l...
  • 2 me toos
  • 4 replies
  • Question
  • Answered
Photo of Thomas Hucke
Channel utilization – Not important for EMC-Netsight?
Looking for software for monitoring our university wireless network based on Extreme Network  wireless controller V2110 and mostly APs 3...
  • 1 me too
  • 6 replies
  • Problem
  • Solved
Photo of M.Nees
Are Enterasys GVRP and XOS MVRP compatible?
We used C5 Enterasys Switches (Edge) and S-Series (Core) in our network.To provide VLANs automatically to the switches we are using GVRP....
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Florian Knorn
Using SNMP, how can I find the VLANs associated with an interface
Using SNMP, how can I find the VLANs associated with an interface? I know I can snmpwalk 1.3.6.1.4.1.1916.1.4.17.1.1 but that only start...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Philipp Tittmann
XOS - clipaging
Hi,  is there a way to disable clipaging on XOS-based switches permanently? The command `disable clipaging`only effects the active ssh/t...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Rod Robertson
Adding a multicast stream using L3
I have added a new multicast stream , I have the server and on layer 2 I can see the correct streams , 239.192.1.56, and 239.192.2.56. on...
  • 1 me too
  • 4 replies
  • Problem
  • Not a Problem
Photo of Johan Hendrikx
open device terminal in XMS (web version Netsight) cann't connect to switch with SSH
How can I change the port number op the open device terminal ? Now I got  an error: Failed to connect
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Bartek
NAC and hosts with static IP issue
Hi Everyone, I have NMS+NAC version 8.0.5.18 with environment where almost all end systems are using static IP addresses (there is no DH...
  • 1 me too
  • 2 replies
  • Problem
  • Solved
Photo of info@systemhaus-genthin.de
How to switch off LED of a single AP 7522 permanently ?
I have s small private customer solution with 5x  AP7522, without central Controller. one of the AP ́s is the virtual Controller. custom...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Andre Brits Kannemeyer
3912i 802.15.3 support
The 3912i support  802.15.4 for connectivity of IoT Sensors and Devices. How do we use this feature? (Zigbee Gateway) Looking at the AP...
  • 2 me toos
  • 2 replies
  • Question
  • Answered
Photo of M.Nees
WLAN AP: Defining AP-Name within CLI Prompt
Because i am working for deeper troubleshooting directly on AP CLI, I am looking for a way how to see/set the AP-Name within CLI Prompt. ...
  • 6 me toos
  • 5 replies
  • Idea
  • Under Consideration
Photo of M.Nees
EOS - S-Series: Sending Trap if broadcast suppression limit is reached
Is it possible that s-series (or K or 7100) are send an traps if the broadcast supression threshold value is reached ? I do that with al...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Andrea
Enterasys S-series: syslog not working
Hi, on my campus we have one Enterasys S8 and two Enterasys S3. We configured syslog logging in all of them, but we can't receive any s...
  • 1 me too
  • 2 replies
  • Problem
  • Solved
Photo of Andre Brits Kannemeyer
440 G2 POE+ not working to Extreme Wireless 3935i
Hi Community It would seem that the Extreme 440-G2 does not detect the power requirements for a Extreme 39xx series AP correcly. With d...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Lutha
ssh and telnet access
Hi Guys I am trying to setup telnet and ssh access on my extreme swicthes i ahve already tried the suggested solutions but they do not s...
  • 1 me too
  • 4 replies
  • Problem
  • Solved
Photo of M.Nees
EXOS specifiy source interface for sntp, download image or download url
We have a X450-G2 with 16.1.3.6. This switch is the router of a branch. Unfortunately the router-transfer nentwork is not part of VPN I...
  • 4 me toos
  • 10 replies
  • Question
  • Answered
Photo of Nico Lueck
netscaler/citrix server send gratuitous arp which is not recordnised by S8 Core Switch
Our Customer is using a netscaler. Server (main&backup) is using same IP Address. When there is an failover on server site, the server s...
  • 1 me too
  • 4 replies
  • Problem
  • Solved
Photo of Rory Schmitz
How to Display Summit X400 Series LLDP Information onto Cisco IP 79xx series Web GUI
Hi, We're migrating away from Cisco switches and onto the Summit X400 series switches.  We currently have Cisco IP Phones (7900 and 9900...
  • 1 me too
  • 7 replies
  • Question
  • Answered
Photo of Somebo O'Rother
a way to update port aliases, via LLDP?
New (to enterprise networking) guy--Wondering if there would be a way to update port aliases, via LLDP, to avoid manually having to do it...
  • 1 me too
  • 4 replies
  • Question
  • Answered