Conversations

Photo of PARI ELANSURIYAN
Is there any option to power off the EXOS switches remotely ?
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Athiwat Wongkhumjun
Where I can download EXOS Data Sheet from new web site?
Hi Team, From the new Extreme Networks web site. Where is EXOS Data Sheet? Thank you!
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Brad
Cannot ping in/out of switch but can ping through it
I recently setup a new extreme switch that I am having a problem with. The switch itself is not able to ping out and other devices aren't...
  • 1 me too
  • 9 replies
  • Problem
  • Solved
Photo of Johan Brand
220 LED patterns
We've been doing some office renovations and got a few new cat6 points installed. I have two points next to each other on a wall with o...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Sean Scarfo
How to create an LACP LAG on EXOS 21.1X?
I'd like to create a simple 4 port LAG between an Extreme Switch (x460-G2) and a Brocade switch (that is already successfully setup for L...
  • 2 me toos
  • 3 replies
  • Question
  • Answered
Photo of GONÇALO NUNO CONTENTE PIMENTEL DA SILVA REIS
Edge port topology change
Hi, sometimes i get confused probably because i am missing something very obvious but im unable to see it. For some reason a port config...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of GONÇALO NUNO CONTENTE PIMENTEL DA SILVA REIS
EXOS 22.3.1.4 not responding to OID (extremeStackMemberTable)
Hi all, I used to have all my access switch on 21.1.3.7 and used this OID (1.3.6.1.4.1.1916.1.33.2) to get stacking information. After up...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Lutha
Port channel between x440g2 48 p and cisco cat 6500
i have configured port channel on my cisco and extreme switch but when i connect the interfaces the port channel doesnt come up not sure ...
  • 1 me too
  • 8 replies
  • Problem
  • Not a Problem
Photo of George Schoggins
Does anyone have a working config for a shoretel phone using LLDP on XOS 22.1.4.4
LLDP and Shortel
  • 1 me too
  • 3 replies
  • Problem
  • Solved
Photo of dayover1@gmail.com
Address is on the same network as VLAN port_1_vlan!
I want to configure ports like - 192.168.1.x/24 but i have a problem, from 2nd and above vlan, it tells me "Address is on the same networ...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of waqas
Unable to Add L2
Hi Experts, I am getting below error messages on switch logs, Can you please tell me the what causes these errors. The version on BD8806...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Terren Crider
Recommended Edge (user) Port Loop Prevention?
What is the recommended method of loop prevention for EXOS and EOS at the user port?  STP + SpanGuard? Edit:  I may have an answer in EL...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Bobby
block mac address command in switch XOS CLI
I took over an existing enterprise size extreme network, been getting already that people have threats basically sending to third world c...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Mykhaylo Skrypka
Upgrade the X250e-48p directly from 12.0.3.16 > 15.3.5.2
Hi Community, Can l perform direct upgrade from 12.0.3.16 > 15.3.5.2? Switch BootROM: 1.0.3.5 Regards, Mykhaylo
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Angel Pavon
How upgrade BD8810??
Hello. Do I upgrade a BD8810 like Summit Xos ??
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Frank Seidler
Connection between Transceiver MGBIC-LC03 and 10060 !
Hi, I'm searching for experience with the Connection between an switch EOS  A4H with MGBIC-LC03 and a XOS Summit X450-G2 with a 10060 Tr...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Phillip Hood
X620-16x firmware upgrade error - TFTP error file too large for TFTP protocol
I have been trying to upgrade one switch with summitx-21.1.3.7.xos that came out on February 1st and I am having issues.  I have 2 of the...
  • 1 me too
  • 3 replies
  • Problem
  • Solved
Photo of John Wood
ospf
Please help to create ospf. I am a beginner in Extreme switches. Can you recommend how to build a extreme network
  • 1 me too
  • 3 replies
  • Question
  • Answered