Conversations

Conversations 1 - 20 of 21
Photo of Rainer Adam
SecureStack B5/C5 feature AP-Aware not found
I search for a possibilty to authenticate an Extreme Networks AP on G3 and C5 switches via 802.1x, but the traffic that comes bridged@AP ...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Andre Brits Kannemeyer
S series VSB LFR
Hi We have installed two S6 chassis, bonding them using VSB. Each chassis has one fabric blade and one IO blade. The VSB bonding ports ...
  • 3 me toos
  • 1 reply
  • Question
  • Answered
Photo of Alan Martinez
Unable to create vlan interface
I try to create a new vlan and assing a IP but when add the IP Address to vlan I had a message: "Could not Create Vlan Interface". >se...
  • 1 me too
  • 2 replies
  • Problem
  • Solved
Photo of Dusan K.
AP3805i-ROW won't register with V2110 anymore (same VLAN)
AP's in the same subnet as the physical topology (esa0, PHY, AP Registration checked). APs were already registered with EWC (initially de...
  • 2 me toos
  • 11 replies
  • Problem
  • Solved
Photo of Naoman Ghani
How to clear Maclock "Last Violating MAC address" field
For many years our C5 stacks (edge switches) have the following configuration for all edge ports... set maclock enable set maclock trap <...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Juanm
800-Series Fails to Deliver PoE
800-Series Fails to Deliver PoE
  • 2 me toos
  • 2 replies
  • Problem
  • Solved
Photo of M.Nees
EXOS: comparable command like "logging synchronous" available
On Cisco IOS during debug sessions "logging synchronous" will make handling command execution mutch more easier. Is there on EXOS an co...
  • 2 me toos
  • 4 replies
  • Question
  • Answered
Photo of Rafael Antunes
Doubt about temperature thresholds (CHASSIS S8)
Hi guys. What's thresholds (temperature) are the indicated for correct operations the Enterasys S8 chassis? I did find it in the docum...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Chris Bresching
a2h124-48 Firmware update failed CRC check all the time
Hi, i have an older a2h124-48 Switch with Firmware 02.01.01.x . I tried to update these to 03.03.06.01 - allways with the result: TFTP ...
  • 1 me too
  • 4 replies
  • Problem
  • Solved
Photo of Steve Ballantyne
Guest WiFi sign in page - change display size for mobile (TOO SMALL!)
Sorry all, I know this gets asked a lot. And I wouldn't ask again - except that the old threads on this topic don't seem to align with th...
  • 5 me toos
  • 2 replies
  • Problem
  • Solved
Photo of Thibault Rochette
C4110-2 wrong role applied to wifi users
Hi everyone, We have a problem, which one appears randomly and we have many diffulcuties to identify the origin and how to resolve it. ...
  • 1 me too
  • 4 replies
  • Problem
  • Solved
Photo of Jeremy Bullock
How to setup bridge at controller
We are currently running on Bridge at the AP and would like to move to Bridge at the Controller for one of our wireless VLANs. I'm just ...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of networks
7100-Series / ACL / Access Control List / Limitations
We want to transfer a large ACL from a DFE module (with Advanced Licence) to an 7100 (about 300 entries). We can only enter 171 lines, th...
  • 1 me too
  • 20 replies
  • Problem
  • Solved
Photo of Elena Madrigal
Migrating settings from cisco virtual controller V2110 to C5210
Hello  i have currently two V2110  controller in HA. And we have purchased 2 – C5210s and we be installing them soon. My question is how ...
  • 2 me toos
  • 3 replies
  • Question
  • Answered
Photo of Mark Robinson
LACP ports from B3 vs B5 Enterasys Switch
Is there a difference between these two switches when configuring LACP?  We replaced a B3 with a B5 switch with identical configuration a...
  • 1 me too
  • 4 replies
  • Problem
  • Solved
Photo of Anton Sax
A2 series - Change from dhcp to static ip
Hy, we want to change a2 switch from dhcp to static ip, but the switch won't let me: TST2-A2-5(rw)->set ip address 10.142.14.5 mask 255...
  • 1 me too
  • 6 replies
  • Problem
  • Solved
Photo of Mandar Kulkarni
Default vlan Logic
Lets say I have host which was connect to port 3  on vlan 10 then someone moved that cable and and connected to port 5 which is on defaul...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Laura
Adding new APs, and they are showing up as "Inactive"
I'm installing new APs, and I can approve the APs, but they are showing up as "Inactive". They have a 00.00.00.00 addresses. I have tried...
  • 1 me too
  • 11 replies
  • Problem
  • Solved
Photo of Edward Oseko
v2110 with ap 3825e and ap 3865e
I have been trying to get a virtual V2110  to work with AP 3825E and 3865E . From the controller I can ping the dhcp ips add assisgned to...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Philipp Tittmann
S4 DHCP Bindings
Hi Guys,  on a S4 Switch i have a dhcp pool enabled on a vlan. when i do "show ip dhcp binding" there are a lot of addresses with status...
  • 1 me too
  • 3 replies
  • Question
  • Answered