Conversations

Conversations 1 - 20 of 33
Photo of Tino
XOS Stack Individual Member Uptime
how can I see the individual uptime of switches in a stack ? We have switches in a stack rebooting and when I telnet into each slot it st...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Alok Shukla
I have error in MLAG. help to resolve this issue
  • 2 me toos
  • 4 replies
  • Question
  • Answered
Photo of Ranjith
inter vlan issue
i have 2 networks,these networks are in different core switch,i created different vlans in both switch,now inter vlan is not working what...
  • 1 me too
  • 5 replies
  • Problem
  • Solved
Photo of Alok Shukla
Summit X440 series switch
Want to create alternative stacking on Summit X440-24p series switch??????
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Ayush Gupta
Does MSM-A and MSM-B for BD-8810 have individual MAC addresses apart from Switch's MAC address?
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Bnoba CEO
High "Rx Over" Error on a Port
Hi, I have a port on a switch that is not congesting and the utilization is lower than 20 percent. Yet, Rx over error is so much - can r...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Dave Hanna
Removing stacking from: BootRom
So we had a couple of switches that had previously been in a 4-slot stack. Stacking was disabled but when 2 of these switch where put in ...
  • 2 me toos
  • 4 replies
  • Question
  • Answered
Photo of Tim Smith
Convert Cisco CLI to Extreme EXOS CLI
Hi all, May I ask does Extremenetworks provide convert tool to translate cisco CLI to Extreme CLI? Is someone could help me to translate ...
  • 2 me toos
  • 4 replies
  • Question
  • Answered
Photo of Nico Lueck
Summit Stack - Daisy chain to ring topologie
Hi community, I just added 2 switches to a existing stack (2 switches). Now my question, when changing the topologie from daisy chain to...
  • 2 me toos
  • 2 replies
  • Question
  • Answered
Photo of Alok Shukla
Backup of switch x620-16x
During taking backup of switch configuration, the ACL configuration is by default downloaded or we can manually be downloaded?????
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Tiburcio Jr Coronado
how to delete vlan in Netsight 7.0.9.4 , or modify the edit membership of vlan
Trying to delete vlan from 10 aggregation Nodes, vlan no longer in use. No option to by pass START-MIX-PROTECTED-VLAN-DELETE operation fa...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Alok Shukla
Trunk problem
I am trying to make Trunk "Ruckus Controller" and "Ruckus AP" over on Extreme Switch X440, but it's not making trunk while on access port...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Long Tran
ExtremeSwitching Dual 10GbE Upgrade License
Hi all,I have X440-G2-24t with S/N 1711N-40484 and  Voucher ID : “Dual 10GbE Upgrade License”. I active them in Extreme Portal à Assetsà ...
  • 2 me toos
  • 2 replies
  • Problem
  • Solved
Photo of Igor
Stacking speed for X440-G2
Could please explain me which stacking speed on X440-G2? I read documentation and see 10Gbit/s. This is full or half duplex? Can I reach ...
  • 2 me toos
  • 2 replies
  • Question
  • Answered
Photo of Sarah Seidl
Replacing slot #1 XOS
Hello, I am trying to understand the proper method for replacing slot #1 (<-- specifically) in an XOS stack. Example: (2) 460-48p switche...
  • 1 me too
  • 7 replies
  • Problem
  • Not a Problem
Photo of Ilya Semenov
Does VIM4-40G4X allow to use stack and 40Gb ports for access simultaneously?
Hello, I have two 670v-48t with VIM4-40G4X cards. May I use two ports from VIM4-40G4X for stacking and the rest two ports - for attachi...
  • 2 me toos
  • 1 reply
  • Question
  • Answered
Photo of Weda
How to weight the route more one VLAN over another VLAN when I use OSPF ?
How to weight the route more one VLAN over another VLAN when  I use OSPF ?  Can I do this changing the OSPF VLAN cost  ?
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Thavamani Shanmugam
How to upgrade EXOS in multiple Swtiches Simultaneously
How to upgrade EXOS image in more than 40 number of X440-G2 switches simultaneously. Please share the procedure to install EXOS image sim...
  • 2 me toos
  • 5 replies
  • Question
  • Answered
Photo of Anders Sjökvist
Port bounces up and down once after reboot: X670G2-48x-4q
After reboot of the switch some port are bouncing up and down one time. We don't see any reason for this and it's causing traffic loss fo...
  • 1 me too
  • 7 replies
  • Problem
  • Not a Problem
Photo of AIT Support
Adding a second PSU 10931 module on X460
Dear Community If I want to add a second internal power supply to a Summit X460, should I first switch off the switch, or can you conne...
  • 1 me too
  • 2 replies
  • Question
  • Answered