Conversations

Conversations 1 - 20 of 372
Photo of Salvatore Aurnia
After reboot, in X620-x16 switch link down with SFP mini-GBIC
I have a problem with switch extreme X620-16T (10G) (IMG 21.1.3.7), SFP transceivers are used (therefore at 1G). I do the following steps...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of SH
XMC python modules used in example scripts
Hello,often in the XMC example scripts functions from the module "xmclib" or "device" are used.Is there a documentation what functions ar...
  • 1 me too
  • 6 replies
  • Question
  • Answered
Photo of Julian Eble
MPLS FAT Label
Hello, By reading this article http://packetpushers.net/fat-or-entropy-label/ I`ve been wondering if Extreme could implement something l...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of jeronimo
Topology: MLAG
Hey,Can you validate that the following is a valid setup using MLAG.Sites A and B contain two MLAG peers each.There are two independent l...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of jeronimo
EXOS: give more feedback on CLI
Hey, I've been playing with EXOS and I noticed the following. "configure vlan x delete port 2" does not throw an error when the port wa...
  • 1 me too
  • 3 replies
  • Idea
  • Under Consideration
Photo of PARI ELANSURIYAN
ELRP warning message --WARNING:
ELRP warning message --WARNING: Port 4:9 does not belong to VLAN_108! but configuration taken it will affect if suppose that port in any ...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Sulaiman Al Darmaki
MLAG configuration
Hi, im having a virtual lab, where i try to practice MLAG, the topology is as in the diagram now i have a problem and some questions re...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Tim Black
What are my options for EXOS Network Management Automation
Hello, my team has developed an automated system for testing my company's networked products. I am in the process of integrating this sys...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Jake Koch
EXOS MLAG and bonded S8s
Hello Extreme Hub, I have a questions regarding EXOS MLAG and bonded S8s 1st here is the scenario: I have a customer with bonded S8s t...
  • 1 me too
  • 6 replies
  • Question
  • Answered
Photo of kjstech
How to create routed GRE Tunnel from X450G2 to Cisco Router?
Ok guys, I have a new site with two X450G2's running system version 22.5.1.7 and Advanced Edge License.  I currently have a high speed WA...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of welisson
Does Extreme MPLS work with 6PE and 6VPE ?
Hello Everyone, I've been chasing this information into the documentations, nonetheless I can't find recent information about that. Can ...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of theoadon
Replacing a Cisco 3845 router and Cisco 3560 switch with extreme products
HI There,We asked from a customer to replace his network equipment.Now the customer's site is using a Cisco 3845 router and Cisco Catalys...
  • 1 me too
  • 9 replies
  • Question
  • Answered
Photo of Alok Shukla
Want to configure etherchannel over point to point link of different ISP
Want to configure LAG over point to point link of different ISP? In below figure, we want to configure Fa0/1 and Fa0/2 LAG and both port ...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Gregory Krueger
Recommendation for configuration of Management port when Summit x440-24P is only switch in the network
I'm looking to see if anyone can give me a recommended configuration for the management port for a small network.  I'm an automation engi...
  • 1 me too
  • 9 replies
  • Question
  • Answered
Photo of Visconti
Show IP address of specific port
I have finally use netsight console v8 after using GUI web version.Can I create a flexview that can show me the IP address of all port of...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Timothy Corcoran
Displayed Routes in "sh ipr" different than expected based on LSDB
Issue:Why does sh IPR treat destination networks differently even though at first glance they should be treated the same?   Refer...
  • 1 me too
  • 2 replies
  • Question
  • In Progress
Photo of Maple Wang
Can't set factory default or upgrade for summit x450a-48t
Hi, we are using summit x450a-48t with exos 15.3.2.11, recently, we want to reinstall or set factory default to it, but it didn't work. ...
  • 1 me too
  • 7 replies
  • Problem
  • Solved
Photo of Thyago C. Rodrigues
Help with an MPLS/OSPF architecture
Hi dears,I would like a help with the architecture displayed below. Please feel free to make any comment.Network descriptions and require...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Roman Serbski
Shortest path with ISLs?
Hello,Sorry if it has been cleared before, but is there any short-path intelligence with ISL links?We have a fabric of six 6740T-1G VDXs ...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Ronie Singh
MPLS route is still active in routing table even its corresponding OSPF route is not listed
Hi There, I found MPLS route is still active in routing table even its corresponding OSPF route is not listed in routing table. Ori  Dest...
  • 1 me too
  • 10 replies
  • Question
  • Answered