Conversations

Conversations 1 - 20 of 399
Photo of Ronald Dvorak
AP3915i mounting option
Why is the logo upside down if mounted on the wall with the default option. Marketing 101 = brand recognition
  • 2 me toos
  • 7 replies
  • Question
  • Answered
Photo of Steve Ballantyne
Lousy, stupid, stubborn old radiology devices (and the Summit stack that hates them)
Howdy folks,I am trying to finish up a job replacing some very old Cisco 3750's with a new stack of Extreme Summit 450-G2 switches runnin...
  • 1 me too
  • 3 replies
  • Problem
  • In Progress
Photo of Ilya Semenov
10Gb SFP+ 10GBASE-T capabilities
Hello, everyone, I've found a very intersting item in the price: 10338 10Gb SFP+ 10GBASE-T 10Gb SFP+, 10GBASE-T RJ45, 30m with Cat6a C...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Ronie Singh
MPLS route is still active in routing table even its corresponding OSPF route is not listed
Hi There, I found MPLS route is still active in routing table even its corresponding OSPF route is not listed in routing table. Ori  Dest...
  • 1 me too
  • 10 replies
  • Question
  • Answered
Photo of Antonio Opromolla
XMC 8.2 and missing Topology Definitions and Services Definitions nodes in the Global Tree view
Hi, I've installed a new XMC version 8.2.0.89 with an evaluation license and also installed the Fabric Manager VM also version 8.2.0.89. ...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of RAJA RAMESH JAMI
dual Master same time 3 different stacks
*00:04:96:82:4d:0b 1     Active      Master   CA- 00:04:96:82:4c:fd  2    Active       Master   CA- 00:04:96:7e:29:97 7     Active  ...
  • 1 me too
  • 11 replies
  • Problem
  • In Progress
Photo of Keith Olmstead
XOS LACP Share Algorithm L2 how can I make load balance?
I have X670 Core with LAGS set up to edge using multicast traffic, but traffic is not balancing using L2 or L3. Is there an extra config ...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Alexander Bauer
Are there any effects at the network if i configure the MLAG LACP address later?
I want to configure the mlag lacp mac adresse in a productiv network. Are there any effects at the network? I will configure the mac of t...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Alok Shukla
I have error in MLAG. help to resolve this issue
  • 2 me toos
  • 4 replies
  • Question
  • Answered
Photo of Andre Brits Kannemeyer
OSPF new vs old - LSA Type 11
Hi CommunityI have stumbled across a issue I have with an OSPF network.As usual the communities comments would be appreciated.The client ...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of M.Nees
Netsight V8 - WebShell - logging functionality
Currently i do some lab test to get in contact with the new Netsight V8. Now SSH is directly useable within OneView (Web Browser). It wo...
  • 2 me toos
  • 10 replies
  • Question
  • Answered
Photo of Brent Addis
Eaps 4 switch ring w/ MLAG
Hi,I have a bit of confusion around the configuration of the design on a network we have built.We have four sites, connected by 2 * 10 gi...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of João Alexandre
Can the x450-g2-24t-10ge4 support up to 24k ipv routes ? Can this sw support up to 2k hosts ipv4 ?
Can the x450-g2-24t-10ge4 support up to 24k ipv routes ? Can this sw support up to 2k hosts ipv4 ?
  • 2 me toos
  • 3 replies
  • Question
  • Answered
Photo of EtherNation User
ELRP with dynamically changing vlan membership
Create Date: Mar 13 2013 9:48PM Hello Everyone, I've been looking at ELRP to help prevent L2 loops. Our switches (one section of them)...
  • 1 me too
  • 22 replies
  • Question
  • Answered
Photo of Martin Flammia
ELRP across multiple stacks
Hi, Have a scenario where we are using ELRP, which works great for disabling ports on the same stack but we have a stack in the same roo...
  • 1 me too
  • 6 replies
  • Question
  • Answered
Photo of David Coglianese
Does the X590 support LRM optics?
We recently found the data sheet for the X590 which could be a very attractive solution if it supports LRM optics. We know not all SFP+ ...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Ronie Singh
Appreciate if someone can explain clearly the use case of command "enable ospf mpls-next-hop " & "enable iproute mpls-next-hop".
Appreciate if someone can explain clearly the use case of command "enable ospf mpls-next-hop " & "enable iproute mpls-next-hop".
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Andreas Larsen
Ansible for XOS
Have anyone done any playbook work with ansible for Extreme networks ? Is there anything done in the ansible-galaxy part or anything done...
  • 4 me toos
  • 17 replies
  • Question
  • Answered
Photo of kang zhao
Does X770 support IPv6 port mirroring
Hi There, I have enabled port mirroring in X770 but can not find IPV6 packages. We user port, enable both direction My question is , d...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of priti
10 gig port of extreme X460G2-24x-10G4. It is showing low Rx power
HI experts ,I have connected one server on 10 gig port of exterme X460G2-24x-10G4. It is showing low Rx power and port is not coming up. ...
  • 1 me too
  • 3 replies
  • Problem
  • Not a Problem