Conversations

Conversations 21 - 40 of 369
Photo of Scott Landry
For (8) x620-8t-2x in a ring, is it possible to disable stacking for the 2x ports (9 and 10) and configure these as ISL uplink ports ?
For (8) x620-8t-2x in a ring configuration, is it possible to disable stacking for the 2x ports (9 and 10) and configure these as ISL u...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of M.Nees
EXOS: UPM Script - port number in log message
Today i play around with a UPM Script which refresh nodealias table after a port link down. # # Module upm configuration. # create upm pr...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Arjumand Qazi
XMC ZTP+ configuration (migration of config from old to new switches)
Need to migrate running config from around 40 existing X460's switches to new X460 switches. I was told ZTP+ can help in this regard, i ...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of brian osgoiod
Extreme equivalent of trunking
I am having difficulty understanding how multiple vlans are transported between extreme switches (not stacked) and how they are physicall...
  • 1 me too
  • 8 replies
  • Question
  • Answered
Photo of Karina Del Moral
error ipv4 multicast entry
I open a GTAC case, I just put in this x440 stack (today first day of production) and I got the ipv4 multicast entry error any suggestions?
  • 1 me too
  • 13 replies
  • Question
  • Answered
Photo of Alok Shukla
Could we create Stacking over two switches?
Could we create Stacking over two switches?
  • 2 me toos
  • 6 replies
  • Question
  • Answered
Photo of Alok Shukla
MLAG is good or bad in this topology diagram?
We have Core A and Core B Cisco switch's both are working in active-active and deployed in Building A, and in our environment, all access...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of M.Nees
EXOS: execute command several times and prompt output to CLI
In EOS (S-Series) i use sometimes these to execute a custom command several times and look at the output: loop 10 1 -r sh flowlimit stat...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Martin Flammia
VRRP best practices, preempt, tracking, fabric routing, accept-mode, host mobility
Hi There, Apologies for this question being a little long.... Just looking into the communities thoughts around some best practices aro...
  • 3 me toos
  • 4 replies
  • Question
  • Answered
Photo of Terren Crider
A little ACL help
I'm developing an ACL to allow guest use of certian resources on my network.  In the end, the guest network will be its own subnet.  So, ...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Siva
Two extreme switch can ping each other
Good day all I have been looking around if this has been ask and answer it seems I can’t find any. I have a problem with two extre...
  • 1 me too
  • 9 replies
  • Problem
  • Solved
Photo of Alok Shukla
How do upgrade SFP 1gb link to 10 gig onx440
How do upgrade SFP 1gb link to 10 gig on x440 switch?
  • 1 me too
  • 7 replies
  • Question
  • Answered
Photo of Susana Tovar
Help, I need to configure elrp
Hello All, I need configure elrp in switch X460-24t version 16.1.4.2 patch1-7 but i don't know what option to choose, i have this option...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Alok Shukla
MLAG issue
we want to createing MLAG between 2 switches X620. During MLAG creation does IP of all VLAN between 2 switches be same using or same subn...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Martin Flammia
MLAG vs Stacking Explained
This question comes up a lot, of which myself have been guilty of asking. Was recently asked to define the differences between the two, a...
  • 3 me toos
  • 2 replies
  • Question
  • Doesn't Need an Answer
Photo of Marvell Kay
Cant SSH2 to Extreme switches via Ubuntu
We recently enable SSH2 in our environment.  I am able to SSH to Cisco switches without any issue but can not to any Extreme switch.  I c...
  • 1 me too
  • 9 replies
  • Problem
  • Solved
Photo of Alok Shukla
VRRP priority
I have configured MLAG(X670) on two switch and want to configure VRRP active-active can we use same priority level on both switches?
  • 1 me too
  • 4 replies
  • Problem
  • Solved
Photo of Alok Shukla
ISC
During ISC creation can we create of other VLAN trunk ? Suppose i have 5 vlan's on switch-1 and we create ISC link between Switch-1 and S...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Alexandr P
BGP AS-PATH preferred route
Hello, all! Does anybody faced with issue, BGP routes with the same Weight and LPref and Summit is choose preferred route with larger AS...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Karina Del Moral
XOS upgrade question
We have our big maintenance window on a weekend, I need to upgrade the XOS image on several devices, can I pre-load the image and install...
  • 1 me too
  • 6 replies
  • Question
  • Answered