Conversations

Conversations 61 - 80 of 369
Photo of Christoph
MACsec?
Hello,are there any plans to implement  IEEE 802.1AE on Enterasys / Extreme switches and APs in future? I think especially for inter swit...
  • 2 me toos
  • 5 replies
  • Idea
  • Implemented
Photo of Sergey Vekli
VPLS+MLAG+ISC
Hi all. Config. We have two X670 with MLAG and MPLS/VPLS enabled, some ports use MLAG.  We have shared group of 4 ports for ISC link bet...
  • 1 me too
  • 5 replies
  • Problem
  • Solved
Photo of andreas
IPv6 IBGP Loopback peering
I'm trying to setup ibgp ipv6 between two x460-g2 running version 22.2.1.5-patch1-4  I have two ebgpipv6 neigh on one router and one ibg...
  • 1 me too
  • 2 replies
  • Problem
  • Solved
Photo of Ilya Semenov
Does Extreme have transceivers which allow to use duplex cable for 40Gbps, like Cisco BiDi?
Hello, CISCO has a technology which allow us to use pair of optical cables for 40Gbps, known as Cisco BiDi (https://www.cisco.com/c/en/u...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Ian Broadway
LACP via MLAG config check
Hi All, First time configuring a server with LACP via two switches with MLAG configuration. Can someone just confirm this is correct? ...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Eric Burke
LLDP not working for polycom, but working for Cisco phones on x460-G2
We have two phones, one Polycom VVW310 and a Cisco 7911 plugged into sequential ports on our stack.  They are configured with the same LL...
  • 1 me too
  • 3 replies
  • Problem
  • Solved
Photo of Mrxlazuardin
VXLAN Routing
Hi, By http://documentation.extremenetworks.... it seem that EXOS has not supported VXLAN L3 gateway, but it has supported VXLAN L2 ga...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Trevor Jackson
Extreme Summit Switch Appears to not be Sending any OSPF Hellos
I am trying to get an OSPF adjacency between a Summit  X460G2-48p-G4 and a Palo Alto VM-100. I have done this quite a few times already a...
  • 2 me toos
  • 10 replies
  • Problem
  • Not a Problem
Photo of bw447
EXOS how to reset a port to factory default
Is there a way to reset a port back to factory default. For instance if I have a port with 7 vlans tagged and 1 untagged with elrp on ...
  • 1 me too
  • 14 replies
  • Question
  • Answered
Photo of Nick Yakimenko
ELRP per vlan - is that possible?
XOS firmware Port configured as trunk and have some vlans tagged ELRP in case of loop in one of the vlans, disables a link on a port Is t...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Bill Handler
XOS - NetSight Compass not showing IP Address (Version 6.2.0.199)
When performing a Compass search in NetSight 6.2.0.199 with Summit X460-G2 switches, only MAC Addresses are displayed.  No IP Addresses a...
  • 2 me toos
  • 8 replies
  • Problem
  • Solved
Photo of Alexander
policy based routing summarize
Hi, i have a question about policy based Routing! I wirte the Poliy like this: entry REDIRECT80 { if {     source-address 192.168....
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of EtherNation User
ELRP with dynamically changing vlan membership
Create Date: Mar 13 2013 9:48PM Hello Everyone, I've been looking at ELRP to help prevent L2 loops. Our switches (one section of them)...
  • 1 me too
  • 22 replies
  • Question
  • Answered
Photo of Martin Shadbolt
Can I save the results of a script to file?
I need to login to a switch, run a 'show' command, then save the output to a file. I need to do this for 30+ switches, and would preferab...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Sofiane ould Mohammedi
run vm xos on vmware workstation 11
Hi All, I tried to set up a new virtual switch xos (xos 21.x)on vmware workstation 11 so I managed to get it installed but the network ...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of sumeet
creating double tagged packet from untagged input and vice versa
hi i am using extreme x460-24t switch. My aim is to feed packet (say ping) from laptop to port , say IN , and get double tagged packet ou...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Linus Lindblad
MLAG and Vxlan mixing.
I've been trying to figure out what makes MLAG implementation in a vxlan enviroment different from other more 'regular vlan' implementati...
  • 1 me too
  • 9 replies
  • Question
  • Answered
Photo of Support Forte
NetSight 8 Https Connection Problem
Hi everyone, I have deployed NetSight 8.0.2.48 version to VM, both VMWare, and VirtualBox to test. Although I can ping the NetSight serve...
  • 1 me too
  • 2 replies
  • Problem
  • Not a Problem
Photo of Sarah Seidl
Run report to find failed POE switches?
Hello -We have x460-48p gen1 switches system wide. When one fails POE we know about it b/c poe devices like cameras or WAPs are down whic...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Erik Auerswald
127-Bit IPv6 Prefixes on Inter-Router Links with EOS (S-Series)?
Hi, has anybody tried to implement /127 IPv6 transport networks with S-Series switches? Is some special configuration necessary for this...
  • 1 me too
  • 4 replies
  • Question
  • Answered