Conversations

Conversations 101 - 120 of 401
Photo of andreas
IPv6 IBGP Loopback peering
I'm trying to setup ibgp ipv6 between two x460-g2 running version 22.2.1.5-patch1-4  I have two ebgpipv6 neigh on one router and one ibg...
  • 1 me too
  • 2 replies
  • Problem
  • Solved
Photo of Ilya Semenov
Does Extreme have transceivers which allow to use duplex cable for 40Gbps, like Cisco BiDi?
Hello, CISCO has a technology which allow us to use pair of optical cables for 40Gbps, known as Cisco BiDi (https://www.cisco.com/c/en/u...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Ian Broadway
LACP via MLAG config check
Hi All, First time configuring a server with LACP via two switches with MLAG configuration. Can someone just confirm this is correct? ...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Eric Burke
LLDP not working for polycom, but working for Cisco phones on x460-G2
We have two phones, one Polycom VVW310 and a Cisco 7911 plugged into sequential ports on our stack.  They are configured with the same LL...
  • 1 me too
  • 3 replies
  • Problem
  • Solved
Photo of Mrxlazuardin
VXLAN Routing
Hi, By http://documentation.extremenetworks.... it seem that EXOS has not supported VXLAN L3 gateway, but it has supported VXLAN L2 ga...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Trevor Jackson
Extreme Summit Switch Appears to not be Sending any OSPF Hellos
I am trying to get an OSPF adjacency between a Summit  X460G2-48p-G4 and a Palo Alto VM-100. I have done this quite a few times already a...
  • 2 me toos
  • 10 replies
  • Problem
  • Not a Problem
Photo of bw447
EXOS how to reset a port to factory default
Is there a way to reset a port back to factory default. For instance if I have a port with 7 vlans tagged and 1 untagged with elrp on ...
  • 1 me too
  • 14 replies
  • Question
  • Answered
Photo of Nick Yakimenko
ELRP per vlan - is that possible?
XOS firmware Port configured as trunk and have some vlans tagged ELRP in case of loop in one of the vlans, disables a link on a port Is t...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Bill Handler
XOS - NetSight Compass not showing IP Address (Version 6.2.0.199)
When performing a Compass search in NetSight 6.2.0.199 with Summit X460-G2 switches, only MAC Addresses are displayed.  No IP Addresses a...
  • 2 me toos
  • 8 replies
  • Problem
  • Solved
Photo of Alexander
policy based routing summarize
Hi, i have a question about policy based Routing! I wirte the Poliy like this: entry REDIRECT80 { if {     source-address 192.168....
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Martin Shadbolt
Can I save the results of a script to file?
I need to login to a switch, run a 'show' command, then save the output to a file. I need to do this for 30+ switches, and would preferab...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Sofiane ould Mohammedi
run vm xos on vmware workstation 11
Hi All, I tried to set up a new virtual switch xos (xos 21.x)on vmware workstation 11 so I managed to get it installed but the network ...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of sumeet
creating double tagged packet from untagged input and vice versa
hi i am using extreme x460-24t switch. My aim is to feed packet (say ping) from laptop to port , say IN , and get double tagged packet ou...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Linus Lindblad
MLAG and Vxlan mixing.
I've been trying to figure out what makes MLAG implementation in a vxlan enviroment different from other more 'regular vlan' implementati...
  • 1 me too
  • 9 replies
  • Question
  • Answered
Photo of Support Forte
NetSight 8 Https Connection Problem
Hi everyone, I have deployed NetSight 8.0.2.48 version to VM, both VMWare, and VirtualBox to test. Although I can ping the NetSight serve...
  • 1 me too
  • 2 replies
  • Problem
  • Not a Problem
Photo of Sarah Seidl
Run report to find failed POE switches?
Hello -We have x460-48p gen1 switches system wide. When one fails POE we know about it b/c poe devices like cameras or WAPs are down whic...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Erik Auerswald
127-Bit IPv6 Prefixes on Inter-Router Links with EOS (S-Series)?
Hi, has anybody tried to implement /127 IPv6 transport networks with S-Series switches? Is some special configuration necessary for this...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Tom
Trying to use the dedicated rear 21Gbps stacking ports on X450-G2 but no bueno
I'm wondering what I'm doing wrong here, I currently have a stack of 5 switches (All X450-G2 using the front 10Gb ports) Slot-1 ex-460-c...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Mrxlazuardin
Hybrid QSFP28 Breakout
Hi, I know one 100Gbps QSFP28 can be splitted to 4 25Gbps SFP28 or 2 50Gbps QSFP28 using breakout cable. Is it possible to have both t...
  • 1 me too
  • 8 replies
  • Question
  • Doesn't Need an Answer
Photo of wang maple
is there easier way to configure trunk port in extreme switch
I'm just starting to use extreme switch, and the switch type is X450a-48t, and SW version is 12.0.3.16. when I configure the trunk port i...
  • 1 me too
  • 12 replies
  • Question
  • Answered