Conversations

Conversations 161 - 180 of 387
Photo of Pa Trick
What are the Command to passtrough Customer-LACP through an Extremeswitch with sw 22.1
Setup: Point to Point connection with two Extreme x620. We have setup a VMAN for transparent Service.  Customer use LACP on both end that...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Sumanta Ghosh
IPv6 address on VLAN error
Getting error while trying to assign IPv6 interface to a vlan. IPv6 forwarding is already enabled on the VLAN, along with port tagging. ...
  • 1 me too
  • 12 replies
  • Problem
  • Solved
Photo of Wesley Braunberger
Links using SFPs from RAD in rear ports of X440-G2 don't become active
Trying a SFP from RAD in a Extreme X440-G2-24t-GE4. using the SFPs in the back of the chassis. When connected the state on the switch is...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Ilya Semenov
Could this script interrupt SNMP process and cause high CPU utilization?
Hello, everybody! Every morning I get the email from Netsight: Netsight Critical Alarm: Device Down Device: 192.168.251.161 (This is a...
  • 1 me too
  • 3 replies
  • Problem
  • Solved
Photo of Danial Jalil
IP connectivity
I am trying to connect switch using management port. The ip assigned to management port can be pinged but when i ping the default gateway...
  • 1 me too
  • 10 replies
  • Question
  • Answered
Photo of Thavamani Shanmugam
DoS-Protect Implementation Issue...
We are facing some issue with TCP Synflood in our Network. Now we are trying to implement DoS-Protect to prevent this. We have enabled t...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of bw447
python app logging
I'm trying to setup a python app just so that I can test out the logging function. This switch that I'm running this on is an x460 run...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of LEM
Traceroute through MPLS cloud
Traceroute through MPLS cloud.I have a simple demo stand for MP-BG. Here is how it looks: CE1-PE1-PE2-CE2 We have BGP peering between CE...
  • 1 me too
  • 15 replies
  • Question
  • Answered
Photo of Ko Saw Gyi
How To Config PBB Network in Extreme Switch
Hi All,               I would like to request, how to configure PBB in extreme XOS with cli. Please kindly help me. BRs, S.SBD
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Sikander Shah
Hi community, I am facing problem connecting X440 48 to X620.
Hi community, I am facing problem connecting X440 48 to X620. All 48 ports of X440 working fine, but from 49 to 52 not working? please ...
  • 1 me too
  • 6 replies
  • Problem
  • Solved
Photo of Ko Saw Gyi
can't upgrade to XOS 16.2.1.6 on X480 48t
Hi All  I can't upgrade to XOS 16.2.1.6 on X480 48t. It display tftp error. But I can upgrade another version on X480 48t. Please help me.
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Alan Santoro
x450-G2 won't boot after enabling stacking on master
Hey folks! I'm working on a stack of (3) X450G2-48p-10G4 to replace our old X350 user stack.  The new switches have 16.1.0.18 on them fr...
  • 1 me too
  • 2 replies
  • Problem
  • Not a Problem
Photo of Frank
LACP/LAG with 'switches in between' (not true 2-Tier)?
I'm drawing a blank as to "do I do this right, or what do I do wrong?". If you look at the following: Note that there is no ISC/MLAG be...
  • 1 me too
  • 8 replies
  • Question
  • Answered
Photo of vobelic
EtherType 0x0030
I am implementing a tight ACL policy for our storage (NFS) VLAN. Basically the idea is to allow only needed stuff, and block the rest. T...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Sarah Seidl
Purview PV-fc-180 console
Hello, We are trying to hook a purview sensor PV-fc-180 to our tripp-lite serial console switch. We have 9600, 8, none, 1 and no flow con...
  • 2 me toos
  • 7 replies
  • Question
  • Answered
Photo of andreas
bgp log
How do you get bgp to at least log up and down from neigh in the normal log ?  Do I have to configure a specific logfilter ? for these s...
  • 1 me too
  • 8 replies
  • Question
  • Answered
Photo of Dean Ferraro
auto or manual priority for 460G2 switches in a stack?
We used easy stacking to deploy our stacks throughout our deployment of 460 G2 switches. I have noticed that the slot 2 device is now sho...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Jesse Ohlsson
How to create and use configuration templates in Management Center 7?
How do I create and use a configuration template using Management Center (not the legacy application called Inventory Manager)?  I have...
  • 4 me toos
  • 2 replies
  • Question
  • Answered
Photo of Darrin Tingey
Should EDP be turned off on ports that are connected to access points?
EDP
  • 1 me too
  • 9 replies
  • Question
  • Answered
Photo of Jesse Ohlsson
QoS configuration - can someone check my work?
We're an Extreme shop, and I'm the new-ish engineer here.  I'm tasked with configuring up a  replacement X440 switch stack to replace som...
  • 1 me too
  • 4 replies
  • Question
  • Answered