Conversations

Conversations 1 - 20 of 72
Photo of Javier J. Rejon Orellana
Multicast forwading inter-VLAn without default gateway, TTL=1 and PIM enabled
Hello.We have a BD8806 with several VLANs. We have PIM enabled and multicast routing between these VLANs. The problem is the following: ...
  • 2 me toos
  • 2 replies
  • Question
  • Answered
Photo of Ian Broadway
DHCP Standard Practise
I have a question regarding DHCP.  Whats the standard practise for implementing DHCP helpers. Our current setup, we use UDP profile on ...
  • 1 me too
  • 8 replies
  • Question
  • Answered
Photo of Alok Shukla
ACL applying over VLAN
We have three VLAN's all are inter-VLAN routing. VLAN-1= 10.3.1.0 VLAN-2= 10.3.2.0 VLAN-3= 10.3.5.0 My boss wants to VLAN-2 and 3 should ...
  • 1 me too
  • 2 replies
  • Problem
  • Solved
Photo of Rich
ACL counters not showing
Hi,  I have an ACL defined to manage general access between subnets across switches, and as part of that some rules have counters assigne...
  • 1 me too
  • 10 replies
  • Problem
  • Not a Problem
Photo of Victor Vit
Don't see macs in fdb table on x450a-24x
Hello. There is a problem with adding some random client's macs in fdb table on extreme x450a-24x firmware version 15.3.5.2. I see this m...
  • 1 me too
  • 3 replies
  • Problem
  • Solved
Photo of Steve Ballantyne
Slow file copying to site usings Windows SMB over MPLS circuit
Hello folks, This is not necessarily an Extreme Networks specific question, but I am hoping the community here can give me a clue about ...
  • 2 me toos
  • 4 replies
  • Problem
  • Not a Problem
Photo of Susana Tovar
How to connect via ssh from router cisco
Hello All,  My ISP needs connect with switches extreme by SSH from rouert cisco since we want to maintain this connection as contingency...
  • 2 me toos
  • 3 replies
  • Problem
  • Not a Problem
Photo of Mustafa
problems with ip route default
Hello. I have a route table. All routes are directed to 10.106.0.1 as the default route, but I would like to route a single VLAN to anoth...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Fagner
how to lock a static ip in interface port in the switch EXOS 15.7?
  • 1 me too
  • 6 replies
  • Question
  • Answered
Photo of Alexandr P
SNMP for LAG bandwidth
Hello, all! I need to monitor bandwidth of LAG port with SNMP. As I understand for now there is no any OID's for this In EXOS there is o...
  • 3 me toos
  • 2 replies
  • Question
  • Answered
Photo of Jannik Winther
No longer getting Extreme Support emails?
Hello, we are not getting emails on Case updates from Extreme Support support@extremenetworks.com anymore, even though there were se...
  • 2 me toos
  • 2 replies
  • Question
  • Answered
Photo of Rod Robertson
IPV6 broadcast storm, on an IPV4 network
We have a number of printers that by default have IPV6 configured though not used. ( not supported by me ) These printers are also   conn...
  • 1 me too
  • 14 replies
  • Question
  • Answered
Photo of Paul Thornton
IPv6 forwarding issue with OSPFv3 in a user VR
Hi all Before I open a TAC case about this, I'm just trying to find out if anyone else is doing something similar and has the same issue...
  • 1 me too
  • 9 replies
  • Problem
  • Solved
Photo of Alexandr P
Some clients unable receive IP
Hi, all! Have a simple configuration with internal DHCP. 1 client Sansung Galaxy receive IP 0.0.0.0. Change radios as here - {previously...
  • 1 me too
  • 6 replies
  • Problem
  • Solved
Photo of Elie Raad
deny specific prefixes in bgp
Hi,  i am trying to deny exact prefixes 66.133.0.0/23 and 66.133.2.0/23 from being advertised and allow everyhting else  to an iBGP neigh...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Elie Raad
BGP advertise-map in XOS
I have a Multi-homed Routers connected to 2 ISPs. I need to Create like an Advertise-map on the Standby Router connected to the Standby I...
  • 1 me too
  • 7 replies
  • Question
  • Answered
Photo of Claudio Minnetti
Summit X670V-48t - Switchport stuck in ready status
Product Model: Summit X670V-48t-FB-AC Software Version: 16.1.3.6 Ethernet Switchport 1:7 remain in ready status even if a device is conn...
  • 1 me too
  • 6 replies
  • Question
  • Answered
Photo of Trevor Jackson
Configure Flow Redirect with Multiple Match Conditions
I have successfully configured flow redirect a few times using examples from other posts here on the Extreme site such as: https://gtack...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Jarek
Flow redirect with ECMP
Hi, I have checked the doc. and so on... but didn't find answer to my question. Is it possible to do ECMP with flow-redirect ? Example...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Mark Lamond
Basic Policy Based ACL
Hi there, Can anyone explain to my why this basic ACL policy does not work? This is using XOS 22.2.15 on an X450-G2. I want to emulate Ci...
  • 1 me too
  • 5 replies
  • Question
  • Answered