Conversations

Conversations 1 - 20 of 139
Photo of Johan Hendrikx
Syslog display wrong information
I have configured my switch to send messages to the syslog server (XMC).configure syslog add <IP-XMC>:514 vr VR-Default local0 configure ...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Johan Hendrikx
Is there a report or flexview to see what the primairy and secondairy firmware is ?
Is there a report or flexview to see what the primairy and secondairy firmware is ? And which is active ?
  • 1 me too
  • 3 replies
  • Question
Photo of Johan Hendrikx
Where can I find the release notes of V2110-10.41.10.0014
Where can I find the release notes of V2110-10.41.10.0014 ?I looked athttps://www.extremenetworks.com/support/release-notes/But couldn't ...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Aviv Kedem
WING5 with Juniper switches
Hello All, At last few years when i installing WING5 products with Juniper switches it seems layer2 MINT is blocked by switches without...
  • 2 me toos
  • 3 replies
  • Problem
  • Solved
Photo of Network Operation Center
x670-x440 Vrrp change master to backup, not routing
We have 2 stacks both stacks are 1 x460 and 1x440 and an ISC connecting. When we try to fail over to the backup, the backup takes over as...
  • 1 me too
  • 3 replies
  • Problem
Photo of Enrico Celegon
Banner
I would like to configure Extreme 200 series, x460 and x670 to receive cli-banner, MOTD, failed auth, user welcome, ecc... directly from ...
  • 1 me too
  • 0 replies
  • Idea
Photo of Johan Hendrikx
Add a task got err 'Coiuld not lod report'
When I add a scheduled task or edit one, I got the error 'Could not load report
  • 1 me too
  • 4 replies
  • Problem
  • In Progress
Photo of Johan Hendrikx
Cann't reference firmware to stack
why cann't I reference a stack to a firmware release ? 
  • 3 me toos
  • 2 replies
  • Question
Photo of Johan Hendrikx
How can I see the dhcp bindings
How can i display the bindings of a DHCP environment that is configured in a topology that is used in a Wlan configuration within a V2110
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Ian Broadway
10.41.09 Release Notes
Can't find them anywhere through the various document sections? Can someone provide them please Thanks Ian
  • 1 me too
  • 6 replies
  • Question
  • Answered
Photo of Chris McCann
Powering off one AP removes others from wireless domain.
HI, I have a AP7532 and AP6522's in a RF Domain. First problem was I had to do some manual config on our central NX7520 controller as the...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Johan Hendrikx
Verifying NAC Appliance's RADIUS Configuration for each Switch
I've configured radius on the EAC and  a switch in my lab. Also configured SNMP on both devices. Shared secret is the same.  I dubble che...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Johan Hendrikx
difference in number of MU clients
When I open the dashbord wireless in OneView or I look add tab Clients under the menu wireless,  I noticed a differnce in the number of c...
  • 1 me too
  • 1 reply
  • Problem
  • Solved
Photo of Stephen Stormont
Log into switch with LDAP credentials
Currently, we are using accounts created on each switch in order to be able to login. We do have Extreme Management Center 8.x installed...
  • 2 me toos
  • 15 replies
  • Question
  • Answered
Photo of Johan Hendrikx
No DHCP fingerprints in EAC after configuring bootrely to the appliance
No DHCP fingerprints in EAC after configuring bootrely to the appliance. I configured bootprelay to my EAC appliance and noticed that the...
  • 1 me too
  • 4 replies
  • Problem
  • Solved
Photo of Johan Hendrikx
Is it possible to add new device types in OneView?
Is it possible to add new device types in OneView?  I have some HP 1910 in my network a like to see it as a known device
  • 2 me toos
  • 3 replies
  • Question
  • Answered
Photo of Johan Hendrikx
nac display wrong wireless Switchport in NAC v8.1.3.65
In NAC the end-systems are linked to the wrong switchport. Other end-systems are linked to the right switchport.How to resolve?
  • 1 me too
  • 1 reply
  • Problem
  • Solved
Photo of Johan Hendrikx
EWC sends data to Purview. Wan router also see the data
After configuring EWC to send data to PurView Analiticys an strange problem happend.The data that the AP send to Purview  was detected by...
  • 1 me too
  • 3 replies
  • Problem
  • Solved
Photo of Johan Hendrikx
AP3805i connect only at 100 Mb at X440G2-48p-10G4 switch
I have more than 50 AP 3805i connected at X440G2-24p-10G4 and X440G2-48p-10G4 switches. One AP connect with 100 mb instead of 1...
  • 2 me toos
  • 5 replies
  • Problem
  • Solved
Photo of Johan Hendrikx
network performance data is unavailable in OneView
For some reason OneView will not collect data about Network and Application performance.When I look at the impact analsys and put the mou...
  • 1 me too
  • 4 replies
  • Problem
  • Solved