Conversations

Conversations 1 - 20 of 179
Photo of Yves Haslimann
Sending flow data from a switch direct to ExtremeAnalytics (without a flowcollector engine)
Hello everybody I would like to configure the Extreme Switches (x440-G2, with version 22.4) to sending sflow/netflow data direct to the ...
  • 2 me toos
  • 14 replies
  • Question
  • Answered
Photo of Prabhu.M
Does x670-g2 switch support HSRP?
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Saurabh Makkar
Xenpak on port 49 detected, unable to read Oui, possible mdio read error
<Erro:HAL.Port.Error> Xenpak on port 49 detected, unable to read Oui, possible mdio read error <Erro:HAL.Port.Error> summitIsXenpak2Opera...
  • 1 me too
  • 2 replies
  • Problem
  • Solved
Photo of M.Nees
EXOS: UPM Script - port number in log message
Today i play around with a UPM Script which refresh nodealias table after a port link down. # # Module upm configuration. # create upm pr...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of GONÇALO NUNO CONTENTE PIMENTEL DA SILVA REIS
IpArp not learning IP
Hi, i am trying to troubleshoot why IPARP is not showing the IP addresses of edge devices. Slot-1 SEDUCA050100.3 # sh iparp stats ports ...
  • 1 me too
  • 7 replies
  • Question
  • Answered
Photo of Julian Eble
Port Congestion
Hello Community, I have been noted some congestion on ports connected to my GGC port channel and I can't figure out what is happening h...
  • 1 me too
  • 7 replies
  • Problem
  • Solved
Photo of M.Nees
EXOS: execute command several times and prompt output to CLI
In EOS (S-Series) i use sometimes these to execute a custom command several times and look at the output: loop 10 1 -r sh flowlimit stat...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of simon bingham
XOS is it possible to disable a built in stacking port.
XOS is it  possible to disable a built in stacking port. I want this to troubleshoot a possible stacking issue.  does not appear to be po...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Marvell Kay
Python SSH script to log into Extreme switch, run command and save output
I have been trying to write a python script that logins to Extreme switch via SSH2, runs commands and shows output.  I looked at Extreme'...
  • 2 me toos
  • 9 replies
  • Question
  • Answered
Photo of Hasan Güngör
i forgot the my switch's admin account passwaord.. help!!!!!!!!!!!
i forgot the my switch's admin account passwaord.. help!!!!!!!!!!!
  • 2 me toos
  • 5 replies
  • Problem
  • Solved
Photo of Nico Lueck
Best Practice: Replacing Core Stack Master incl. MLAG Master
Hi, customer having Following Setup: Now I need to replace the both Stack master regarding: https://gtacknowledge.extremenetwork...
  • 1 me too
  • 3 replies
  • Idea
Photo of Martin Flammia
Switch port packet capture seeing CPU traffic and odd behaviour
Hi There,Been taking some packet captures directly via the command-line on the switch and seeing traffic that I wouldn’t expect. To take ...
  • 2 me toos
  • 3 replies
  • Question
  • Answered
Photo of Justsomebodi
Network Login 802.1x user VLAN(s) "unknown" on 460 G2 switch with EAC
Hi All Does anyone know why my Radius authenticated users has an unknown VLAN in the switch logs? It does not happen this way on a G1. ...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of kjstech
Question about Jumbo frames on individual ports - do you include the stacking ports as well?
I would like to enable jumbo frames on two ports that will be connecting out to a brocade iscsi/nfs switches.  I have two X690's as my co...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of GONÇALO NUNO CONTENTE PIMENTEL DA SILVA REIS
SNMP OID to get the Switch Model
Hi all, I am trying to query a switch via snmp to get its model, by model i mean to know if a switch is a X450G2-48p-10G4 or X450G2-48p...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Josivan Barbosa
X460-G2 - Default Bootloader is Corrupt
Hello, I have an x460-G2 switch that has the following error: Copyright 2014 Extreme Networks, Inc. Starting CRC of Default image s...
  • 2 me toos
  • 2 replies
  • Question
  • Answered
Photo of Peter
XOS LLDP announce management IP
Hello, is there a way in XOS to announce a IP-address non vr-mgmt/mgmt-vlan in LLDP management address? most of my customers didn't use...
  • 3 me toos
  • 4 replies
  • Question
  • Answered
Photo of Toni Comerma
There is a command in EXOS for "interface vlan x" "shutdown"?
I want to disable the IP of one vlan. In EOS is pretty simple interface vlan X shutdown But I haven't found anything similar in EXOS. T...
  • 1 me too
  • 6 replies
  • Question
  • Answered
Photo of anil
x460-g2 swtich failed again and again
is anyone help...i have x460-g2-48p and x440-g2-24p and both are in stacking... but x460 switch failed 4 times,,i rasied request from RMA...
  • 2 me toos
  • 2 replies
  • Question
  • Answered
Photo of Alexander Prokofyeff
Can I configure LAG from 10G ports on diffrent x440-G2 in SummitStack-V to the 10G core switch?
I will have some x440-G2 in SummitStack-V and Cisco 4500-X in core. Can I configure LAG from 10G ports on diffrent x440-G2 in SummitStack...
  • 1 me too
  • 1 reply
  • Question
  • Answered