Conversations

Conversations 1 - 20 of 28
Photo of Keith Obermeier
Summit Stack 450 460 10BT
I have a number of POE devices that operate at 10BT  (yes 10 megabyte) that we plan to deploy.  In my summit switches they are getting PO...
  • 1 me too
  • 2 replies
  • Problem
  • Not a Problem
Photo of TallyRich
Do the BD8806 and BD8810 switches support CoreFlow2.
I need to install Extreme Analytics into a network and the most logical point of monitoring would be a pair of BD8810 switches in the cor...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of htw
EXOS equivalent for EOS "show port advertise"?
Hi, with EOS I can use "show port advertise" to see the advertised speed of a network device which is connected to the switch, f.e.: SWIT...
  • 2 me toos
  • 2 replies
  • Question
  • Answered
Photo of Tim Black
Trouble connecting to Management port with either direct or switched ethernet connection
I have a windows 10 host with an ethernet interface (configured with static ip 192.168.1.2/24) that is directly connected to the Manageme...
  • 1 me too
  • 10 replies
  • Question
  • Answered
Photo of Visconti
Show IP address of specific port
I have finally use netsight console v8 after using GUI web version.Can I create a flexview that can show me the IP address of all port of...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Gihan Kankanamge
Is there any Power supply for Extreme Summit X450a-48t switch?
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Johannes Grewe
Are ERS3600 and VSP7200 Switches "Common Criteria" ready? (CC Version 3.1)
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Visconti
netsight SNMP trap service do not start
My "netsight SNMP trap service" do not start ..can onyone help me?My log trap is empty..... "Unable to find events in log file"While the ...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of julienb
edge-safeguard enabled by default
Hi, Is there a way to enable by default for every ports the STP mode edge-safeguard with bpdu-restrict ? Like the "spanning-tree portfas...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Thavamani Shanmugam
Latency While Pinging Gateway of Vlan's Which is in our Core Switch
Hello, We have a BD8810 core switch and few models of Extreme EXOS Edge switches (like X430, X440, X460). All of our servers are connec...
  • 2 me toos
  • 19 replies
  • Problem
  • Solved
Photo of Alexandr Viktorovich
ExOS rate-limit flood- broadcast Flood Rate Exceeded
Hi everyone. I have some problem with control broadcast in my network. If i set broadcast flood rate in something like 30000, i saw that...
  • 1 me too
  • 7 replies
  • Question
  • Answered
Photo of Paul
EAP port roles on transit switch
Can anyone explain the significance of primary and secondary ports for a transit switch within an EAPS ring? I understand that for a mast...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Alma Gonzalez Constantino
Download extremeXOS 15.2
Hi all: I have to replace a switch with ExtremeXOS 15.2.15, but the spare part has 12.5.4.5, so I think should update the OS in the new o...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of enrico kunert
LACP connected host ---> two tier MLAG <--- LACP connected host
Hi all,we have the following testsetup and i have a question regarding the different ping behavior as shown below... plz have a look and ...
  • 1 me too
  • 8 replies
  • Question
  • Answered
Photo of Waqas Naeem
Switch Flash Corrupted
My customer is trying to upgrade firmware of Summit X350-48t but facing some issue flash corruption. Please advise any fix for corrupted ...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of deepak lagad
Comparison of extreme switches
Where i can find comparison option for different switches?
  • 2 me toos
  • 8 replies
  • Question
  • Answered
Photo of Marcus Mathuni
VLAN Rate limiting on Black Diamond X8
Hi community, we have BlackDiamond X8  Firmware Release 16.1.3.6 how best to configure rate limiting with max 5Gbps (10Gbps available) a...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of RC Barnhart
Utilize Vlans accross Multiple Virtual Routers, help in concept/cfg
I'm attaching a document of my current setup. I'm trying to utilize more of the Virtual Routers of a summit v670 and currently only manag...
  • 1 me too
  • 12 replies
  • Idea
Photo of Nico Lueck
not able to configure sharing when using GNS3
I Start using GNS3 (Version 22.1.1.5) and trying to set up a link aggregation. When using the standard sharing command I'm getting the f...
  • 1 me too
  • 7 replies
  • Problem
  • Solved
Photo of Tomasz Lubas
Will third party MGBIC-LC04 work with X460-G2-48t-10GE4-Base switch ?
Hello, Our customer want to put 100Mb transceivers into sfp+ ports on X460-G2-48t-10GE4-Base switch. Extreme MGBIC-LC04 seems to work. He...
  • 1 me too
  • 2 replies
  • Question
  • Answered