Conversations

Conversations 1 - 20 of 36
Photo of Eric Burke
Enable SummitStack-V on single switch?
In the past, our best practice was to enable stacking on everything (including single switches), allowing for future additions to the swi...
  • 1 me too
  • 6 replies
  • Question
  • Answered
Photo of Robert Zdzieblo
S-series S4 transceiver led indicators
I have noticed on S4 chassis equipped with I/O fabrics modules that transceiver leds are blinking with 2 different colours: most of them ...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Prabhu.M
Does x670-g2 switch support HSRP?
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Alok Shukla
ACL for applying over VLAN
We have 4 VLAN over Core Switch (MLAG configured) VLAN 1: 10.3.1.0 VLAN 2: 10.3.2.0 VLAN 3: 10.3.3.0 VLAN 4: 10.3.4.0 we don't want VLAN...
  • 2 me toos
  • 3 replies
  • Question
  • Answered
Photo of Siva
Two extreme switch can ping each other
Good day all I have been looking around if this has been ask and answer it seems I can’t find any. I have a problem with two extre...
  • 1 me too
  • 9 replies
  • Problem
  • Solved
Photo of Eric Burke
L3 Switch acting as Internet router between /30 and routed subnet (outside of firewall)
Looking for a "best practices" example using an EXOS switch acting as both a private network switch and an internet router.  We have seve...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Martin Flammia
Floating Default Route vs Flow Redirect
Hi, Currently working on integrating a legacy Cisco network with Extreme, where the default route for the interim is to send all traffic...
  • 1 me too
  • 5 replies
  • Question
  • Doesn't Need an Answer
Photo of Arjumand Qazi
Proper steps to Enable SSH on 21.1.3.7 or higher XOS
was trying to enable SSH on XOS device having 21.1.3.7 image did the following steps ena ssh <-- OK generated a private key..  <-- OK ...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Grzegorz Niemiec
Ultra Short Range (USM) modules in X440-G2
Does X440-G2 supports optical modules: Ultra Short Range (USM) SFP+ on 1310 nm? Those modules are without standard but few company’s...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Victor Vit
Supervlan and needless DHCP Requests
Hello. If I use separate vlans on Extreme X450-24 ver. 15.3.5.2 with bootprelay, DHCP works fine for my client-device. At first there ar...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Xperia Go
Main difference between EXOS 16.2.x and EXOS 21.1x?
Hello to the community, Usually for my hardware there are two suggestion EXOS 16.2.2.4 or EXOS 21.1.3.7 (http://www.extremenetworks.com/...
  • 2 me toos
  • 6 replies
  • Question
  • Answered
Photo of Rod Robertson
Do I still need an external router to route between different VR , as teh extreme switch has one mac
I have a customer who needs to route between virtual routers , normally I would do this , with some sort of extrenal routing box ( firewa...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of M.Nees
X460-G2 connecting 10 meter DAC Cable possible ?
we want to uplink several X460-G2 switches via 10 meter Copper DAC Cable to a S4. But it seems not working. Does anybody know if the X46...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Adam
Topology change every 1h
Hello together, we have a big problem on our network, topology change takes place every hour and in the morning sometimes every 3 minutes...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Sarah Seidl
How to test 10g circuit?
We have an x480 with a 10g connection to our provider. Optics are 10g multi-mode to our providers equipment. What would be methods of t...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Andrew Butterworth
SummitStack-V & 1000BaseT SFPs?
The datasheet for the Summit X440-G2 series states "SummitStack-V allows use of standard 10Gb Ethernet cabling and optics technologies"Do...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Waqas Naeem
MLAG versus Stack
I was going through the definitions of MLAG support on Extreme Switches (670, BD8000 & BDX8) and link aggregation on stacked switches (Al...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Daniel Valera
LAG Questions
Hi! I want create a LAG configuration, but i have some questions. 1. can i configure it using ports to diferent slots? 2. once configur...
  • 1 me too
  • 11 replies
  • Question
  • Answered
Photo of David Luna
How to monitor stack switch x440 power down witn snmp
Hi..  I would like to monitor when a switch x440-48t in a stack becomes offline.. (power down) with snmp..   I was trying to use OID ( e...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Edwin
Frequent ARP request broadcast for Who has x.x.255.255? from S-Series root switch in RSTP VLAN
We are getting average of 1 pps and peaks of 60 pps of these packets, from Wireshark trace.Please kindly share information on what is the...
  • 1 me too
  • 8 replies
  • Question
  • Answered