Conversations

Conversations 1 - 20 of 106
Photo of Martin Flammia
Spanning Tree Auto Link-type
Have a question about auto provisioning a spanning tree link type.All the Vlans have been configured for the switch and each added to por...
  • 2 me toos
  • 4 replies
  • Question
  • Doesn't Need an Answer
Photo of Andrew Schulz
Private VLAN routing issue
I've configured a private VLAN for  ports 1 and 2 so that they are isolated from one another. The configuration shown below is how I set ...
  • 1 me too
  • 6 replies
  • Problem
  • Solved
Photo of Mario Cruz Torres
STP Configuration Error
Hello Experts, I'm doing an expasion for a client changing some 1G ports to 10G ports for a inter-switch link. I only add the vlans on ...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of JPC
Netlogin - Dot1X and Mac authentication on the same port
I have netlogin successfully working with 802.1x and MAC-based when a single device is connected. I am now trying to combine this in the...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Sergio Galvez
vrrp announcements flooding
Hi experts,I performed a tcp dump in a server of my current network and I'm getting lots of VRRP announcements in this vlan (where server...
  • 1 me too
  • 6 replies
  • Question
  • Answered
Photo of sumeet
internet access via extreme summit x460-24t switch
Here is the situation I have ether cable coming out from my modem which I connect to my PC , then internet works on that PC. BTW , my PC ...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of glenn bronson
How to configure a mac based VLAN on X670G2 Running 15.6.2.12
I need to configure mac based vlans on the G2 switch such that multiple vlans all share the same port. I am connecting 32 individual sing...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of GONÇALO NUNO CONTENTE PIMENTEL DA SILVA REIS
Rate limit flood counters
Hi all, I have set on my switches the rate limit for broadcast and multicast traffic to 1000 pps, i can see the Flood Rate Exceeded coun...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Thavamani Shanmugam
Latency While Pinging Gateway of Vlan's Which is in our Core Switch
Hello, We have a BD8810 core switch and few models of Extreme EXOS Edge switches (like X430, X440, X460). All of our servers are connec...
  • 2 me toos
  • 19 replies
  • Problem
  • Solved
Photo of Ilya Semenov
Abnormal high CPU utilization on stack
Hello, everybody! I have a stack of 2x460 and 6x440 1st generation summits (8 switches total). The problem is every morning at exactly s...
  • 1 me too
  • 9 replies
  • Problem
  • Not a Problem
Photo of Darren Saliva
Slot-1: Login failed through SNMPv3 - wrong digest
I swapped out a switch in my stack and now i am seeing this error message in the logs. I cannot find anything online for this specific lo...
  • 1 me too
  • 7 replies
  • Question
  • Answered
Photo of jeon min
How to block through UPM ?
I would like to log the port block and MAC address through the UPM through the Mac OUI. Thank you for the UPM setting example. For exampl...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Philipp Tittmann
CoS on XOS Question
Hi guys,  according to this KB Article https://gtacknowledge.extremenetworks.com/articles/How_To/Configuring-QOS-profiles-and-verify-QOS...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Ghost108
SNMP Error #2003
Hello togehter, i have an extreme switch an would like to use snmp. my snmp config looks like this: problem is: my snmp test tool says...
  • 1 me too
  • 21 replies
  • Question
  • Answered
Photo of eyeV
Does switch drop untagged frames on tagged only port?
Hi everybody. I have one question. It very important for me. Let us suppose that I have tagged only port (I mean port where all vlans ...
  • 1 me too
  • 6 replies
  • Question
  • Answered
Photo of David Winter
What is the line length limit on policy file redirect-port-list command?
Is there a line length limit in ACL policy files, if so what is it? Is there a line continuation command to allow for longer command leng...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Salvador Gallo
problem with Config Booted on summit x450-g4
when i configured switch this save configuration but if the switch reboot lost the configuration, i can see this configuration in the swi...
  • 1 me too
  • 5 replies
  • Problem
  • Not a Problem
Photo of Ilya Semenov
UDP port for syslog in 16.x EXOS
Hello, everyone! I have 460-G2 switch with 16.2 EXOS. The problem is I can't configure syslog, using this article: https://gtacknowled...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Julian Eble
Load Sharing VPLS end
Hello Community, I'm having headache about the load-balance on Aggreation Ports. Our scenery is a MPLS network who the end point are co...
  • 2 me toos
  • 30 replies
  • Problem
  • Solved
Photo of Артур Беляков
Hello, please tell me OID SNMPv2c to parameter show man > ssh acces. ExtremeXOS version 15.7.1.4
  • 1 me too
  • 3 replies
  • Question
  • Answered