Conversations

Conversations 1 - 20 of 55
Photo of Jhonn Bejar
LAG sharing packet loss and high latency
I have 2 swtiches X670G2-48x-4q, both are working correctly with a LAG (2 ports), version is EXOS 16.1.3.6-patch1-9 Switch1: enable sha...
  • 1 me too
  • 12 replies
  • Problem
  • Solved
Photo of Ayush Gupta
Could we re-name a Private Vlan?
Could we re-name a Private Vlan?
  • 2 me toos
  • 2 replies
  • Question
  • Answered
Photo of Syed Hammad Jaffery
is intermediate upgrade required if upgrading from present version 12.3.3.6 to 15.3.5.2-patch1-13 for switch model summit X450a
Extreme switch model summit X450a  software needs to be upgraded to 15.3.5.2-patch1-13 . Present version is  summitX-12.3.3.6.xos.  Can w...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Josh
Kernel Warnings snoop_cache_unresolved
Hi Guys Having a load of these warnings pop up in the logs on my stack and I don't seem to find anything on the forums about it. <Warn:...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Chip
Containers Support
Does Extreme support containers? Similar to Cisco's Service Containers?
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of simon bingham
What process is this, mcmgr
MSM-A  mcmgr         n/a  n/a  6.2 38.1 33.1 32.6 32.8 45.5 175756.29  223851.09 Does anyone know what process this is ? it ...
  • 2 me toos
  • 1 reply
  • Question
  • Answered
Photo of laurie
Bootprelay configuration
HiWe have a D series Extreme switch and would like to enable bootprelay so clients can receive their addresses from the companies DHCP se...
  • 1 me too
  • 8 replies
  • Question
  • Answered
Photo of Tom Taylor
STP topology changes
I've been trying to track down an issue with STP in one of our branch offices, for some reason STP has an immense amount of STP changes l...
  • 2 me toos
  • 3 replies
  • Question
  • Answered
Photo of Tim Schlueter
There is no command for enable auto-provision
I want to auto configure my extreme switches. I read an article where it discribes how to use the cli command "enable auto-provision". Bu...
  • 1 me too
  • 5 replies
  • Problem
  • Solved
Photo of DH
Change algorithm on port share
I have a port share created with custom lacp and need to change it to l2 lacp. Do I need to disable sharing and recreate it or can I chan...
  • 2 me toos
  • 3 replies
  • Question
  • Answered
Photo of Kalil De A. Carvalho
Extreme using radius JUST to authenticate, not for all command verification.
I have a ExtremeXOS version 16.2.1.6 configured. My intention ware just authenticate my users, but I realized when a user pass any comman...
  • 1 me too
  • 7 replies
  • Question
  • Answered
Photo of ahmed Ahmed
extreme 450e booting problem
At the beginning it was a problem with my switch Fans then Then the switch turned off and i can't have an acces to my switch  i tried to ...
  • 1 me too
  • 5 replies
  • Problem
  • Solved
Photo of Adnan
from where i can download firmware of summit 48si
Hello from where i can download firmware of summit 48si  and does 48si with the last firmware has SSH  i didn't find firmware loading  ...
  • 1 me too
  • 7 replies
  • Question
  • Answered
Photo of Benzion Nussbaum
initial setup x250e
I just got hold of a few extreme x250e and I would like to use them to power a camera system that I have ( I am a cisco guy but just got ...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Adnan
How i can enable access list using ip address to ssh login
hello  i am facing a problem when i am using ACL for SSH using this code it deny all the ip addresses to login using ssh  other question...
  • 1 me too
  • 2 replies
  • Problem
  • Not a Problem
Photo of Martin Shadbolt
Simulate a POE "Failed" state?
We are testing some network monitoring rules, and would like to generate events/alarms when a port delivering POE transitions into the 'f...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Luis Melendez
How send a SNMP Traps test to the Network Management?
Hi All, I am working on the integration of Extream Network 450a switch to the Network Management system, the integration is already done...
  • 1 me too
  • 8 replies
  • Question
  • Answered
Photo of Arjumand Qazi
Easy steps to configure SNMPv3 to work with 3rd party NMS
What are the easy steps to configure snmpv3 on XOS switch that will be discovered by 3rd party NMS via snmpv3. in GTAC i can see some co...
  • 1 me too
  • 8 replies
  • Question
  • Answered
Photo of aloeffle
invalid ssh key after config restore
Dear all. ssh is not working after restore a previously saved config. 1. save config new.cfg 2. unconfigure switch all 3. use configura...
  • 1 me too
  • 3 replies
  • Problem
  • Solved
Photo of Jun Papa
from 8-port switch with vlan iptv. TV port hangs. Anybody experience this problem? Thanks
from 8-port switch with vlan iptv. TV port hangs. Anybody experience this problem? Thanks
  • 1 me too
  • 3 replies
  • Question
  • Answered