Conversations

Conversations 1 - 20 of 26
Photo of Ronald Dvorak
v10.41.08 - dashboard health counter not readable
After upgrading to v10.41.08 the Health counters on the dashboard are not within the screen because the description was changed from "Low...
  • 1 me too
  • 6 replies
  • Problem
  • Solved
Photo of Brandon Cuellar
Extreme switches 200 series SFP uplinks are not working
Customer has a 220 series 12 port and 48 port and is trying to connect the 2 via SFP ports on 1/0/13 on the 12, and 1/0/49 on the 48, but...
  • 1 me too
  • 6 replies
  • Problem
  • Solved
Photo of Uber Londoño
7100 Core Switching Capacity
I have a 7100 Switch and I need to know, how many packets in the network it support, how can I obtain a number, eg, 65000 packets per sec...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Ilya Semenov
V2110 ESXi 6.5 migration issues (STATUS: DOWN)
Hello, team, a customer has V2110 ESXi 6.5 installation. Week ago he transferred V2110's VM to another ESXi host, started the machine an...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Robert Zdzieblo
S-series S4 transceiver led indicators
I have noticed on S4 chassis equipped with I/O fabrics modules that transceiver leds are blinking with 2 different colours: most of them ...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Robert Zdzieblo
A case with DHCP traffic seen by Extreme Analitycs
Hello, We recently had a serious problem during customer's migration from old network based on HP stuff to the new one based on pure EXO...
  • Robert Zdzieblo, 7 months ago

  • 2 me toos
  • 0 replies
  • Question
  • Doesn't Need an Answer
Photo of Robert Zdzieblo
How to setup sharing in MLAG for Windows Server NIC Teaming ?
Hello, What is the best sharing algorithm for connecting Windows Server 2012 NIC teaming ? We have a MLAG disign at the core and NIC tea...
  • 2 me toos
  • 1 reply
  • Question
  • Answered
Photo of Robert Zdzieblo
PV-FC-180 GRE tunnel config problem
Hello the Hub ! I need to configure PV-FC-180 to send analitycs data to PV Appliance. I want to have a single interface configuration, w...
  • 1 me too
  • 6 replies
  • Problem
  • Not a Problem
Photo of Martin Flammia
NAC End-system license contradiction?
Hi, When looking at the NAC end-system licensing / capacity there seems to be a contradiction in the figures, but that could be a misund...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Robert Zdzieblo
how to transfer netsight license to new host ?
Hello everyone ! I have a NetSight installation running at the customer. The license NMS-ADV-5 was activated and installed in 12/2016 on...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Alok Shukla
MLAG is good or bad in this topology diagram?
We have Core A and Core B Cisco switch's both are working in active-active and deployed in Building A, and in our environment, all access...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Robert Zdzieblo
Many DHCP scopes on one VLAN segment - it that possible ?
Hello Community ! I am wandering, if the following setup is possible to work: 1. We have a set (let's say 5) of typical /24 subnets. 2. ...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Robert Zdzieblo
Stp config for mlag design
I have a network, where there are two MLAG peers at the core. Each peer is a stack made of one X670-G2 and one X460-G2. At the edge I hav...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Alok Shukla
How do upgrade SFP 1gb link to 10 gig onx440
How do upgrade SFP 1gb link to 10 gig on x440 switch?
  • 1 me too
  • 7 replies
  • Question
  • Answered
Photo of Robert Zdzieblo
X430-8p PoE problem with cameras
I have a X430-PoE switch running 16.2.1.6 EXOS. Customer reports that external CCTV cameras  ocassionally freeze. The only thing that can...
  • 1 me too
  • 2 replies
  • Problem
  • Not a Problem
Photo of Robert Zdzieblo
IP static route limits for EXOS
I need to know what is exact limits for IPv4 static routes and IPv6 static routes in EXOS. In EXOS 22.2 release notes (Limits section, pa...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Robert Zdzieblo
Failover between two V2110 is not working
Hello the Hub ! I have two V2110 controllers running in availability pair mode. Today the primary V2110 suddenly stopped working - don't...
  • 2 me toos
  • 6 replies
  • Problem
  • Solved
Photo of Robert Zdzieblo
SNMP contact lost to EXOS switch on fresh new EMC 8.04
I have a fresh new EMC 8.0.4.54 installation. I have added new X460-G2 device using ZTP+ and everything was fine. However, after 5-6 min...
  • 1 me too
  • 2 replies
  • Problem
  • Solved
Photo of Robert Zdzieblo
Cannot access my transcripts on extremeportal
After recent changes on Extreme's extranet portal I cannot access my certifications transcripts. My transcript list is simply empty. Does...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Robert Zdzieblo
How to schedule commands on X430 ?
Hello, I need periodically to disable PoE on some ports to reset CCTV cameras (eventually reboot the switch). I was able to write python...
  • 1 me too
  • 3 replies
  • Question
  • Answered