Conversations

Conversations 1 - 20 of 76
Photo of ompal Singh
when i assigning tageed portS to vlan black it is showing like this : VLAN vlan black has no valid 802.1Q tag
 configure vlan "black" add ports 5,7 tagged Error: VLAN black has no valid 802.1Q tag
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Eric Burke
Best practices for shared MAC on MLAG peers?
Creating an MLAG between two 440-G2's. The ISC will be an LACP of ports 15 and 16 and if I understand it, this LACP link must have a stat...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Eric Burke
Enable SummitStack-V on single switch?
In the past, our best practice was to enable stacking on everything (including single switches), allowing for future additions to the swi...
  • 1 me too
  • 6 replies
  • Question
  • Answered
Photo of HarrySo
serious issue after enabling udp policy
Hi guys, we need some help! We have serious problems with our X690-G2 switches after enabling a udp policy. In the last weeks we had bro...
  • 1 me too
  • 3 replies
  • Problem
  • Solved
Photo of Joe80
Routing between Virtual Router on Same Switch
Hi  I’m having an issue with trying to route between two VRs on the same switch following the article (https://gtacknowledge.extremen...
  • 1 me too
  • 2 replies
  • Problem
  • Solved
Photo of Johan Hendrikx
configure an ip-address on a PV-FC-180
how can I configure a management IP-address on a PV-FC-180.Iám not familiar with this hardware
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Sean Scarfo
How to setup MLAG between two x460-G2 switches?
I have two x460-G2 10GE4 switches that I'd like to use MLAG across, what's the best way to accomplish this?  The downstream devices will ...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Prabhu.M
Does x670-g2 switch support HSRP?
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Edison
SNMP Fails and the log thata appeared is entity_fru_getinfo: Invalid entity 132
Hi , Our switch X670G2 witch core license an version 22.3.1.4 patch1-4. had a problem witch SNMP, it Is failing for about 5 minutes,  and...
  • 2 me toos
  • 3 replies
  • Problem
  • Solved
Photo of BGP
Bd 8810 Restarted and Lost 30% of Mac Addresses and now Not Learning New Mac Addresses
The BD 8810 rebooted on its own and lost about 30% of already learnt MAC addresses and right now its not learning any new mac addresses ....
  • 2 me toos
  • 4 replies
  • Problem
  • Solved
Photo of GONÇALO NUNO CONTENTE PIMENTEL DA SILVA REIS
Unable to telnet to Slot on a Stack
Hi all, On my access layer switches, which are configured in stacking mode with versions 22.3.1.4 and 21.1.3.7, i am unable to telnet in...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Balaguru S
Is there any bandwidth limitation in Alpine GM-4X switch module?!
Is there any bandwidth limitation in Alpine GM-4X switch module? I know for fact that GM-16T3 module is 4:1 over subscribed. Any such lim...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Ilya Semenov
May I connect with SSH2 or telnet to the decicated MGMT-port (VR-Mgmt VLAN)?
Hello, team! I've configured IPs for MGMT-ports of all my Exteme switches and connected them to dedicated 2960. Ping works fine but I am...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of James A
Remote packet mirror for XOS?
ExtremeWireless has RealCapture, and EOS can mirror into an L2GRE tunnel, are there any plans to add a similar feature to XOS so that I c...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Erwin van Hoof
x670V-48x multicast L3 hardware table full
Hello, At a customer we are using 3 stacks of 3 x670v-48 switches. These are configured native stacking. The multicast used is PIM Spars...
  • 2 me toos
  • 4 replies
  • Problem
  • Not a Problem
Photo of DH
Switch stack uplinks to network
I have a stack of 5 X440-48p G2 switches. I want to have a LAG uplink to the network and am wondering if the 2 ports should be on the mas...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Erik Auerswald
MLAG Peer Alternate IP: Controlling Which Switch Takes MLAG Ports Down?
Hi, MLAG on EXOS allows to configure an alternate IP address for the peer switch, see e.g. How to implement MLAG alternate peer ipaddres...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Waqas Naeem
Dual Stack IPv4/IPv6 Support
Does Extreme Switches support Dual-Stack IPv4/IPv6? If so, does it support on all Summit & BlackDiamond switches? Is there any licensing ...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Bobby Johnson
Unable to update old firmware v11.2.0.15 to v12.5.1.6
During a recent Firmware upgrade on an x450-24t switch, I encountered a problem updating the firmware from v11.2.0.15 to v12.5.1.6.  I a...
  • 1 me too
  • 1 reply
  • Problem
  • Solved
Photo of wenlong wang
I am going to upgrade on BlackDiamond 8800 from 15.6.4.2 to 16.2.3.
I am going to upgrade on BlackDiamond 8800 from 15.6.4.2 to 16.2.3. Is it possible to performing a hitless upgrade. if not, what is the b...
  • 1 me too
  • 2 replies
  • Question
  • Answered