Conversations

Conversations 1 - 20 of 70
Photo of Alok Shukla
How we do implement Stacking enable on already running production environment?
Want to implement Stacking in already running the production environment, do we have required to backup of configuration or again will do...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Alexandr P
switch dont see own S/N
Hello, all! X480-24x(10G4X).4 # sh version Switch      : N/A(-11)     N/A(-11)    Rev 0.0 BootROM: 2.0.2.3    IMG: 16.2.2.4 Does an...
  • 1 me too
  • 1 reply
  • Problem
  • Not a Problem
Photo of Alok Shukla
Can we enable stack on already been configured X440-g2 switches or does we have required default setting for enabling stack?
Can we enable stack on already been configured X440-g2 switches or does we have required default setting for enabling stack?
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of No Kyoung Ki
What is the EXOS License support dyanmic ACLs ?
Hi allI have a some question about dynamic acls in EXOS switch.What is the license can i useing dynamic ACLs in switch ? all license or n...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Tim Smith
Summit stack dual master
Hi expert, My customer X460 stack have dual master several times, may I ask what kind of information I need to ask him to collect for thi...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Ilya Semenov
May I connect with SSH2 or telnet to the decicated MGMT-port (VR-Mgmt VLAN)?
Hello, team! I've configured IPs for MGMT-ports of all my Exteme switches and connected them to dedicated 2960. Ping works fine but I am...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of arabinda mohanty
Is this possible to configure AP-3805i in standalone?
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Martin Flammia
Dual wireless controllers but can only create one DHCP server on the topology of one controller.
Hi, Have a scenario where I've created a Guest wireless that bridges out of the second Ethernet interface on a resilient pair of identfi...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of chahid
ssh module not loaded, set xmod imag as primary?
set the image as primary, actually am facing an issue with ssh "module not loaded" after i have checked the switch i found xmod image not...
  • 2 me toos
  • 3 replies
  • Question
  • Answered
Photo of Saravanamurthy K
How to disable inter vlan routing in AP7522E? In this firmware is 5.8.5.0-016R
  • 2 me toos
  • 2 replies
  • Question
  • Answered
Photo of Ilya Semenov
Some questions about Enterasys Wifi (v2110)
Hello, everybody! Could you please help me with this: "L2 Ports" in Controller--Network - what can I do with L2 ports in this menu? Cou...
  • 2 me toos
  • 2 replies
  • Question
  • Answered
Photo of earroyo
problem with EAPS with shared port down involved
Hi all, We have had a problem with EAPS that has caused a high level CPU of the switches an the increase of traffic through the rings. A ...
  • 1 me too
  • 3 replies
  • Problem
  • Solved
Photo of Resolut1on
How can I troubleshoot the poe switch. all ports suddenly shut down.
How can I troubleshoot the poe switch. all ports suddenly shut down.  the main problem is it was stacked to other switches. I don't know ...
  • 2 me toos
  • 5 replies
  • Problem
  • Solved
Photo of Gary Hartstone
3rd Party Captive Portals
Hi, I have a customer with a mix of Extreme WiNG APs (most sites) and a couple of sites with Rukus APs. Customer is looking for a 3rd Pa...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of jeon min
How to restore factory default AP 4610-ROW?
I have an AP 4610-ROW but I can't loggin because I don't have user and password. How can I make a password recovery or reset to factory d...
  • 1 me too
  • 6 replies
  • Question
  • Answered
Photo of Resolut1on
AP wing 7522 adapt to rfs 7000 controller
I have AP wing 7522  and I don't know how to adapt it to rfs 7000 controller.  Please help me. Thank you
  • 2 me toos
  • 2 replies
  • Problem
  • Solved
Photo of Gihan
How to block torrent download on wing 5.8 controller?
I'm using vx9000 controller and access points are installed different locations. And I need to block torrent download. How can I do it?
  • 2 me toos
  • 4 replies
  • Problem
  • Not a Problem
Photo of Resolut1on
cli different characters/symbols which is not readable.
cli different characters/symbols which is not readable. Kindly help.Thanks
  • 1 me too
  • 1 reply
  • Problem
  • Not a Problem
Photo of Tim Schlueter
There is no command for enable auto-provision
I want to auto configure my extreme switches. I read an article where it discribes how to use the cli command "enable auto-provision". Bu...
  • 1 me too
  • 5 replies
  • Problem
  • Solved
Photo of Adnan
from where i can download firmware of summit 48si
Hello from where i can download firmware of summit 48si  and does 48si with the last firmware has SSH  i didn't find firmware loading  ...
  • 1 me too
  • 7 replies
  • Question
  • Answered