Conversations

Conversations 1 - 20 of 301
Photo of Stephen Stormont
Is this QOS configuration really doing what we want it to?
Our VoIP phones send traffic with a DSCP value of 46.  The phones are connected to a Summit X440-G2 stack in a VLAN called "VoIP" that ha...
  • 3 me toos
  • 4 replies
  • Question
Photo of Matt Dillion
Extreme should include a Table of Contents section in their release notes, especially when the document is 156 pages long.
Extreme should include a Table of Contents section in their release notes, especially when the document is 156 pages long. Likewise, when...
  • 1 me too
  • 6 replies
  • Idea
  • Planned
Photo of mathews b thomas
what are the commands for taking take logs in core switch...
commands for taking logs in core switch
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Bruno
Lag X460G2 CCR1009
Hi, im having a issue while tring to bond 2 ports between a x460-g2 and a mikrotik ccr1009. My TX traffic get balanced but there is no wa...
  • 1 me too
  • 6 replies
  • Problem
  • Solved
Photo of Sarah Seidl
x460-48p (gen1) with v.80 stacking - can't get it to work when replacing a device
Hello, We have a stack of x460-48p (gen 1 NOT gen 2) running code 16.2.2.4 patch 1-3.  We had one slot reboot periodically (had tried rep...
  • 1 me too
  • 9 replies
  • Problem
  • Not a Problem
Photo of Danial Jalil
ACL for add-vlan-id
I want to add an ingress ACL to a port that adds a vlan to an untagged traffic. if the traffic is tagged it should add a second vlan. fol...
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of kjstech
Mac based port security and removing / modifying configuration
I was trying to experiment with the EXOS version of what we do on our Cisco switches which is mac-address based security tied to a port. ...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Tim O'Donnell
Can you preconfigure slot numbers on new switches going into an existing X450-G2 stack or do they have to be done at the time of install?
I have an existing stack with 2 nodes already.  I am adding 3 additional switches to the stack.  Can I preconfigure the 3 new switches as...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of mavsx .
MLAG Setup, only one Link for now?
I have just added a 450g2 to my environment. Ideally, i'd have more than 1 fiber strand going from this idf to the MDF where the 670s res...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Ian Broadway
Switch UpTime
Any records on longest switch uptime?  AandE-USER-SW1.1 # sh sw SysName: AandE-USER-SW1 SysLocation: AandE Ground Floo...
  • 2 me toos
  • 3 replies
  • Question
  • Answered
Photo of Yusuf Kabbara
Create a loop storm in network "educational Purpose"
Hello I am working on a network with  Ring topology X440 Switches And I'm looking for a scenario to get a broadcast storm "loop" for te...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Carsten Volmer
Enable ssh2 or telnet on XOS without using the console port
Hello, at all! I have made a mistake by disabling ssh2 and telnet on an X460G2 (fw 22.4.1.4). And now i can't manage the switch per remot...
  • 1 me too
  • 7 replies
  • Question
  • Answered
Photo of Angel Pavon
Hello. Please Help!! X460G2 is running with formware version 22.1.1.5.
My X460G2 was rebooted and upgraded to firmare version 22.1.1.5. This was intermittent about six hours. Then I rebooted again and its up....
  • 1 me too
  • 5 replies
  • Question
  • Answered
Photo of Martin Flammia
Stop layer 2 loop with legacy to MLAG pair
Hi, The design intention is to provide connectivity to VLAN X & Y should either one of the legacy cores fail, unfortunately it has to be...
  • 2 me toos
  • 5 replies
  • Question
  • Answered
Photo of David Gardner
Newb Stacking question
Hi all, I have a question regarding stacking. We purchased 3 X450e-48p switches off of EBay, and I want to stack them. I found an article...
  • 1 me too
  • 14 replies
  • Question
  • Answered
Photo of Dave Hanna
Removing stacking from: BootRom
So we had a couple of switches that had previously been in a 4-slot stack. Stacking was disabled but when 2 of these switch where put in ...
  • 2 me toos
  • 4 replies
  • Question
  • Answered
Photo of Sandeep Rajguru
How to check XOS lag/lacp port speed details?
In EOS we have different lag ports like lag.0.x so using lag port status we can check and identify that the attached port is in dormant s...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Terren Crider
Show Port with VLAN name instead of # of VLANs
I have EXOS 21.1.  I would like to know if there is any way to get the output of show port to show all of the VLAN names instead of the n...
  • 1 me too
  • 10 replies
  • Question
  • Answered
Photo of Yusuf Kabbara
MSM B does not synchonize with MSM A
Hello,  We have a BD8806 with two MSM-48c slots. but Backup slot B is not syncing with slot A, I checked Memory usage and only 4% is use...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of MUNIR ENG
What is port congestion?
what is Congestion Port ? what is the normal value of per port?
  • 1 me too
  • 10 replies
  • Question
  • Answered