Conversations

Photo of Walt Witkowski
Comments welcomed on multicast configuration
Running two S4 cores, each with a VRRP instance to 25 individual closet switch stacks.  I am enabling IGMP on each network in each core t...
  • Walt Witkowski, 5 months ago

  • 1 me too
  • 0 replies
  • Question
Photo of Walt Witkowski
where is xos 22.4.1-patch1-2
xos 22.4.1.4 is on the download page.  release note 22.4.1-patch1-2 states that it resolves the issue of EMC or SNMP changes not being sa...
  • 1 me too
  • 4 replies
  • Question
  • Answered
Photo of Walt Witkowski
When will new EMC software be released?
Currently using Netsight/EMC  8.1.0.52 and realizing issues in viewing vlan information on several switch versions.  Was told this versio...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Walt Witkowski
Version 22.1.1.4 default tacacs shared secrets change daily
Just started to upgrade to 22.1.1.5  and noticed that our daily archive picks up a change to the switches configuration everyday.....  Th...
  • 2 me toos
  • 2 replies
  • Problem
  • Solved
Photo of Walt Witkowski
c3 factory default does not delete saved configs or log files
setting c3 to factory defaults does not delete saved configs or log files.  Is there an easier way to delete multiple files other than cl...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Walt Witkowski
Aruba model 320 ap's cannot draw enough POE from SSA
Aruba AP model 320 goes into low power setting when connected to POE on SSA.  I set the inlinepower port capability to 8023at for 34w but...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Walt Witkowski
Need a step by step procedure for replacing a fabric card in an S-4 with different version OS
Have an S-4 chassis with single fabric card that needs to be replaced.  I'm sure the replacement module is of a different OS version than...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Walt Witkowski
Can I create two default routes in S4-
We currrently have a 1gb link between S4 and External FW.  We want to add a 10gb link and then remove the 1gb.  The 10gb link is a differ...
  • 1 me too
  • 3 replies
  • Question
  • Answered
Photo of Walt Witkowski
uptime of switch shorter than last change
SSA ver 07.71.02.0005   SSA uptime shows 188 days  but it also shows ports with a last change of 435 days or  343 days as an example.  I ...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Walt Witkowski
Why numerous ARP's from 0.0.0.0 or 169.X.X.X
S4 cores show repeated messages--(approx.5-10/sec) of "Recieved ARP on vlan XXXX but there is no path to the sender IP address 0.0.0.0 (o...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Walt Witkowski
OID used in "Basic Policy" flexview for "Default Role"
Sorry if this is duplicate post.  I need to construct a flexview in Netsight that displays PVID and policy "Default Role" per port.  The ...
  • 1 me too
  • 2 replies
  • Question
  • Answered
Photo of Walt Witkowski
Vlan tagged policy mappings on C3
Hello all!   I am trying to set  vlan mapping to policy on a trunk port of a C3.   I did check port level mappings enable under the polic...
  • 1 me too
  • 1 reply
  • Question
  • Answered
Photo of Walt Witkowski
How is port type determined for Policy Manger "Port Type" display
 Would anyone know how the port type is determined for policy manager display in the "Details View" tab?  I have ports that are set with ...
  • 1 me too
  • 1 reply
  • Question
Photo of Walt Witkowski
Port Default Policy Role between Console and Policy Mngr is out-of-sync
Why would Console and Policy Mngr differ when viewing the default port policy role that is being applied.  Policy Mngr is showing in one ...
  • 1 me too
  • 1 reply
  • Question
  • Answered