2016-08-01: New GTAC Knowledge Articles July 24 - July 30 2016

[Ken_Thomas]

Here are the new articles that were published July 24 - July 30 2016 in GTAC Knowledge:

Sunday, July 24, 2016:
Hostname is not resolved via DNS while initiating Telnet/SSH/SCP/TFTP from switch
Pre-registration portal CSV has incorrect value for "password" field in the CSV template download
NetSight is not using correct license resulting in lowered device limits
Large delay between host and user authentication using NAC
Understanding NAC - Basic operation of authentication and authorization engine

Monday, July 25, 2016:
How to Obtain and download EXOS
Switch cannot detect the serial number
What base license level is the X620 shipped with?
When changing port partition on an X770 switch, does the switch need to be rebooted?
Interface in Created VRF Does Not Reply to Ping from Global VRF
Does EXOS support Port-Specific VLAN Tag?
How to configure traps on Exos

Tuesday, July 26, 2016:
SNMP Process Running High and EXOS Switch Lost Contact to NetSight
Can the second port on an IdentiFi Wireless AP be used as a data port to connect a PC?
IdentiFi Wireless AP not registering to controller due to Non-secure tunnel error
What does "Total number of IGMP data packets switched" counter mean in l2stats
1G SFP in SFP+ Slot causes LAG Trunk Group Speed of 10000
EXOS: Error message noted - "Kern: MM-A: everestBcmpktToSkb: Could not get pif for slot=3 port=-1"
Unexpected errors seen in the logs when configuring CVID ranges on a CEP port
How do i take a packet capture of the management port?
NAC/Extreme Control -How to terminate a session after a specified amount of time

Wednesday, July 27, 2016:
S-Series Not Forming Adjacency with Neighbor
Pim Video Stream is Not Inter-VLAN Routing on EXOS Switch
Cannot SSH to S-Series
Getting IP connectivity on a EXOS switch
Cannot create Meter in EXOS because of default port groups
Port not properly passing traffic after netlogin authentication when netlogin mode is set to optiona...
Can SSH/Telnet be disabled or enabled during the ZTP+ (Zero Touch Provisioning Plus) configuration
What configuration is needed for ZTP+ (Zero Touch Provisioning Plus)
Blade reset with tFujiAge]fujiAgeTransId error

Thursday, July 28, 2016:
Wireless users unable to pass traffic
SecureStack Interface Trap Shows rtr.0.x Instead of vlan
PIM command not showing up in CLI on Securestack
When special characters are used in the location field in the AP config on the wireless controller, ...
IdentiFi AP3825i-1 are not broadcasting SSID
How many Cards Should be in a HAU Group?
Does EXOS support ISIS as IGP protocol for RSVP-TE?
All traffic are denied by dynamic ACL when the deny rule is removed and added back in EXOS 15.3 or h...

Friday, July 29, 2016:
What is Co and Adjacent Channel Interference
Matrix-X Does Not Add Port to VLAN
Does the Identifi controller support direct LDAP lookup for management login ?
Configure NAC To Use The TLS Client Certificate's Common Name As The Username
How to troubleshoot and debug ZTP+ on Extreme Control Center and ZTP+ devices
Multiple AP3610s crashing and rebooting on the 9.21.xx firmware track
Extreme Access Point AP3825 crash, with 'kernel: kTrapMonitor: NOTE: temporary wdog hit' error
Does ZTP+(PLUS) work on a EXOS stack?
SSA chassis not displaying all slots in Policy Manager
iOS Devices Showing Not Connected When They Are Connected
How to Change the OneView Device Polling Cycle

Saturday, July 30, 2016:
none

[SusanV]

Ron, we recieved the article feedback and we'll review the content and get it updated. Thank you.

[Ronald_Dvorak]

Thanks for the information I'll do that.... 🙂

[SusanV]

Thank you again Ron for all of the feedback. Nice talking with you this week.

[SusanV]

Happy to have a call with you Ron. Meanwhile, there are processes in place to improve the article referenced above. Feedback as well as Demand & Usage are the foundation of our improvement process for KB articles. We're constantly striving to get better. I appreciate your input.