cancel
Showing results forĀ 
Search instead forĀ 
Did you mean:Ā 

Any way to adjust MESH roaming time?

Any way to adjust MESH roaming time?

Andrew_Webster
New Contributor III
Hi,
Setup is RFS4000 + 4x AP6522 + 2x AP6522 setup as client bridges on vehicles.
I am noticing that roaming is taking about 4 seconds to complete when the vehicles move from one AP to the next (speed is slow, approx. 5 Km/h). The roaming duration is causing the client application to fail because the data stream is cut-off for 4 seconds while the roam is taking place. The applications is PLC traffic.
The wireless radios are using 5GHz non-DFS channels.
Signal levels are good, typically around -62 to -57dBm at the vehicle.

Is there any way to make the roaming process go quicker ?

I'm seeing this in the logs during roaming, it seems process is taking 3 seconds from start to finish according to the logs, but I'm seeing about 4 seconds of data loss in total.

Is the radio actually turning off and back on again during the roam?
2017-10-06 12:05:07 TV01 MESH MESHPOINT_ROOT_CHANGE Meshpoint 'BRIDGE' root changed from B4-C7-99-E7-B6-C2 to B4-C7-99-E9-17-42 via next hop B4-C7-99-E9-17-42
2017-10-06 12:05:04 TV01 DIAG NEW_LED_STATE LED state message RADIO_2_52G_LED_ON from module DOT11
2017-10-06 12:05:04 TV01 RADIO RADIO_STATE_CHANGE Radio 'TV01:R2' changing state from 'Initializing' to 'On'
2017-10-06 12:05:04 TV01 DIAG NEW_LED_STATE LED state message RADIO_2_52G_LED_ON from module DOT11
2017-10-06 12:05:04 TV01 RADIO RADIO_STATE_CHANGE Radio 'TV01:R2' changing state from 'On' to 'Initializing'
Relevant configs:
meshpoint BRIDGE
description Bridge mesh for vehicles
meshid BRIDGE
beacon-format mesh-point
control-vlan 61
allowed-vlans 1,60-61
security-mode psk
wpa2 psk 0 xxxxxxxxxxxxxxxxxxxxxxxxx
no root...
profile ap6522 AP-Bridge
...
interface radio2
meshpoint BRIDGE bss 3
...
meshpoint-device BRIDGE
root
monitor critical-resource action no-root
monitor primary-port-link action no-root
exclude wired-peer mint-level-1
acs channel-width 5GHz 20MHz
... profile ap6522 AP-TV
...
interface radio2
meshpoint BRIDGE bss 3
...
meshpoint-device BRIDGE
no root
path-method mobile-snr-leaf
acs channel-width 5GHz 20MHz
service meshpoint loop-prevention-port ge1 The only device overrides on the APs are "no ip igmp snooping".

Thanks!
6 REPLIES 6

Alona
Extreme Employee
Again - what you have configured - is not supported. You need to use a different features.

Andrew_Webster
New Contributor III
Thanks for all the suggestions.
rf-domain does have "channel-list 5GHz 36,40,44,48,149,153,157,161"

The system has been operating since early 2014, so the 6522 was the best fit at that time, and the roaming issue may or may not have been present since the beginning, but only now the application is affected.

Phil_storey
Contributor
AP7532 - work well as a bridge

Timo1
New Contributor II
Maybe you should exchange the APs again a client bridge. We always use client bridges instead of APs as client bridge. Works perfect.
GTM-P2G8KFN