AP7532 Mesh GE1 port configuration

  • 0
  • 1
  • Question
  • Updated 2 months ago
  • Answered
I have a Mesh network set up with 2 AP7532. One is in the garage and I want to connect a PC to via ethernet. It is possible to configure GE1 port to connect to computer?

I tried enabling the port, but doesnt seem to be helping.

!
! Configuration of AP7532 version 5.9.2.0-032R
!
!
version 2.5
!
!
client-identity-group default
 load default-fingerprints
!
ip snmp-access-list default
 permit any
!
firewall-policy default
 no ip dos tcp-sequence-past-window
!
!
mint-policy global-default
!
meshpoint-qos-policy default
 rate-limit meshpoint to-air
 rate-limit meshpoint from-air
 rate-limit neighbor to-air
 rate-limit neighbor from-air
!
wlan-qos-policy default
 qos trust dscp
 qos trust wmm
!
radio-qos-policy default
!
wlan wlan1
 ssid wlan1
 vlan 1
 bridging-mode tunnel
 encryption-type ccmp
 authentication-type none
 wpa-wpa2 psk 0 0123456789
!
meshpoint nateMesh
 meshid nateMesh
 beacon-format mesh-point
 control-vlan 1
 allowed-vlans 1
 security-mode psk
 wpa2 psk 0 0123456789
 no root
!
!
management-policy default
 no telnet
 http server
 https server
 rest-server
 no ftp
 ssh
 user admin password 1 344fb3d332a61eb6e616cee030d0567207d82164eac42b4dad6fd80f99375b6e role superuser access all
 snmp-server community 0 private rw
 snmp-server community 0 public ro
 snmp-server user snmptrap v3 encrypted des auth md5 0 admin123
 snmp-server user snmpmanager v3 encrypted des auth md5 0 admin123
!
profile ap7532 default-ap7532
 autoinstall configuration
 autoinstall firmware
 crypto ikev1 policy ikev1-default 
  isakmp-proposal default encryption aes-256 group 2 hash sha 
 crypto ikev2 policy ikev2-default 
  isakmp-proposal default encryption aes-256 group 2 hash sha 
 crypto ipsec transform-set default esp-aes-256 esp-sha-hmac
 crypto ikev1 remote-vpn
 crypto ikev2 remote-vpn
 crypto auto-ipsec-secure
 crypto load-management
 crypto remote-vpn-client
 interface radio1
  wlan wlan1 bss 1 primary
 interface radio2
  wlan wlan1 bss 1 primary
 interface ge1
 interface vlan1
  ip address dhcp
  ip address zeroconf secondary
  ip dhcp client request options all
 interface pppoe1
 use firewall-policy default
 use client-identity-group default
 rf-domain-manager capable
 logging on
 service pm sys-restart
 router ospf
 adoption-mode controller
!
rf-domain default
 country-code us
!
ap7532 XXXXXXXXXXXXXXXXXX
 use profile default-ap7532
 use rf-domain default
 hostname ap7532-XXXXX
 area Garage
 interface radio2
  meshpoint nateMesh bss 2
 meshpoint-device nateMesh
!
!
end
Photo of Nathan Derichsweiler

Posted 2 months ago

  • 0
  • 1
Photo of Daren Ellis

Daren Ellis, Employee

  • 400 Points 250 badge 2x thumb
Hi Nathan,

You did not specify which config you are presenting.
Also you did not mention if the Mesh was established or not,
In either case the configuration seems incomplete.

Please make the following setting changes and retest.


On both devices
!
firewall-policy default
no ip dos
no ip-mac conflict
no ip-mac routing conflict
no stateful-packet-inspection-l2
!

Root Device (Mesh point needs to be on BSS 1)
!
interface radio2
  meshpoint nateMesh bss 1
  no dynamic-chain-selection
 meshpoint-device nateMesh
  root
  preferred interface 5GHz
  path-method uniform
!


Non Root device (Mesh point needs to be on BSS 1)
!
interface radio2
  meshpoint nateMesh bss 1
  no dynamic-chain-selection
 meshpoint-device nateMesh
  no root
  preferred interface 5GHz
  path-method uniform
!

Notes:
We would not recommend broadcasting a WLAN and utilizing the Mesh on the same radio as that reduces performance (If you are not planning on having wireless clients on the 5Ghz band please remove the WLAN).

Please also use static channel and power assignments for the radio the mesh is assigned to.
In your case radio 2