Auto on/off at X670

  • 1
  • 1
  • Question
  • Updated 3 years ago
  • Answered
Hi Everyone :), I have some question regarding auto on /off at extreme x670,

1. I want to auto on speed 100 duplex full, but there are errors like this
Error: Speed specified is not supported on port 6.
and then i checked the type in this port is BaseT

SW-02-L1-01.1 .2 # sh ports 6 information detail
Port:   6(port_test):
        Virtual-router: VR-Default
        Type:           BASET (Industrial Temperature)
        Random Early drop:      Unsupported
        Admin state:    Enabled with  10G full-duplex
        Link State:     Ready
        Link Ups:       0        Last: --
        Link Downs:     0        Last: --

        VLAN cfg:
                 Name: Vlan_test, Internal Tag = 10, MAC-limit = No-limit, Virtual router:   VR-Default
        STP cfg:

        Protocol:
                 Name: Vlan_test Protocol: ANY      Match all protocols.
        Trunking:       Load sharing is not enabled.

        EDP:            Enabled

2. current configuration in port 2 is auto on, and I want to change to auto off but could not and there is an error
SW-02-L1-01.2 # configure ports 2 auto off speed 1000 duplex full
Error: Auto negotiation off is not supported on port 2 at 1G speed.

If someone can help It would be greatly appreciated.


Regards
Photo of Irwanto Widiansyah

Irwanto Widiansyah

  • 90 Points 75 badge 2x thumb

Posted 3 years ago

  • 1
  • 1
Photo of Ronald Dvorak

Ronald Dvorak, Embassador

  • 44,984 Points 20k badge 2x thumb
1) auto on, speed 100, duplex full - if auto negotation is set to enabled why would you set speed/duplex.
But here a post about the fibre port regarding auto neg...
https://community.extremenetworks.com/extreme/topics/negotiation_1000_10000_with_x670_and_sfp

2) auto must be on for a 1G port
https://community.extremenetworks.com/extreme/topics/set_speed_and_duplex_command
Photo of Irwanto Widiansyah

Irwanto Widiansyah

  • 90 Points 75 badge 2x thumb
Thanks for replay Ronald,
1. I still do not understand, I have a case that the device connected to the port 6 can only run at 100 Mbps, so what should I do? at this time link still ready
2. by default auto negotiation on the x670 is on or off?
Photo of Ronald Dvorak

Ronald Dvorak, Embassador

  • 44,984 Points 20k badge 2x thumb
1) which GBIC is in port 6 - because in the output it looks like a 10G

2) auto negotiation enabled - but you could check with "show port configuration"
There is one row in the output that show auto neg on/off
Photo of adhe tri martika

adhe tri martika

  • 100 Points 100 badge 2x thumb
Mas Irwanto, tipe x650-24x dan x670 hanya support minimum speed 1g (kecuali port management). Jadi walaupun pake sfp base-t tetap minimum speed 1000/1G.
untuk point 2 g perlu di setting auto off, jika sfp yg digunakan 1g maka akan langsung terbaca 1g kok. mohon maaf jika dirasa kurang
Photo of Daniel Flouret

Daniel Flouret, Employee

  • 7,470 Points 5k badge 2x thumb
Irwanto,

SFP+ ports in X670 are 1G/10G ports only.  They DO NOT support 100M.

If you install a 10/100/1000Base-T transceiver it will ONLY work at 1G.
Photo of Irwanto Widiansyah

Irwanto Widiansyah

  • 90 Points 75 badge 2x thumb
Ronald and Daniel,
Thank you for the explanation,

Mas Adhe,
terima kasih untuk penjelasannya