Error: Incorrect carrier vlan configuration of port 1 in stp domain s1

  • 0
  • 1
  • Problem
  • Updated 4 years ago
  • Solved
I am using the VM image of EXOS.

* X4.86 # sh ver
Switch      : PN:1N2039    SN:123456   Rev 0.1 BootROM: 1.2        IMG: 15.4.1.3
PSUCTRL-1   : PN:MEAD      SN:MD1      Rev 0.1 BootROM: 2.1
PSUCTRL-2   : PN:MEAD      SN:MD2      Rev 1.1 BootROM: 2.3
mouse-usb   : PN:MOUSE     SN:4321     Rev 1.1 BootROM: 4.3
floppy-A    :
PSU-1       : Internal PSU-2 PN:1N2039 SN:12345
PSU-2       : Internal PSU-3 PN:1N2039 SN:12345

Image   : ExtremeXOS version 15.4.1.3 v1541b3 by release-manager
          on Tue Dec 10 15:34:47 EST 2013
BootROM : 1.2


When I enable stp domain I get the error. Not sure why ??

Error: Incorrect carrier vlan configuration of port 1 in stp domain s1

This is my STP config.

* X4.87 # show configuration "stp"
#
# Module stp configuration.
#
configure mstp region 080027921b68
configure stpd s0 delete vlan default ports all
disable stpd s0 auto-bind vlan default
create stpd s1
configure stpd s1 mode dot1w
configure stpd s1 default-encapsulation dot1d
configure stpd s1 add vlan x1h1 ports 1 dot1d
configure stpd s1 add vlan x1h1 ports 2 dot1d
configure stpd s1 add vlan x1h1 ports 3 dot1d
configure stpd s1 add vlan x1h1 ports 4 dot1d
configure stpd s1 add vlan x1h1 ports 5 dot1d
configure stpd s1 add vlan x1h1 ports 6 dot1d
configure stpd s1 add vlan x1h1 ports 7 dot1d
* X4.88 # sh vlan
-----------------------------------------------------------------------------------------------
Name            VID  Protocol Addr       Flags                         Proto  Ports  Virtual
                                                                              Active router
                                                                              /Total
-----------------------------------------------------------------------------------------------
Default         1    ------------------------------------------------- ANY    0 /0   VR-Default
Mgmt            4095 192.168.32.104 /24  ----------------------------- ANY    1 /1   VR-Mgmt
x1h1            101  --------------------------------T---------------- ANY    7 /7   VR-Default
x2h1            102  ------------------------------------------------- ANY    7 /7   VR-Default
x3h1            103  ------------------------------------------------- ANY    7 /7   VR-Default
x6h1            106  ------------------------------------------------- ANY    7 /7   VR-Default
x7h1            107  ------------------------------------------------- ANY    7 /7   VR-Default
x8h1            108  ------------------------------------------------- ANY    7 /7   VR-Default
-----------------------------------------------------------------------------------------------
Flags : (B) BFD Enabled, (c) 802.1ad customer VLAN, (C) EAPS Control VLAN,
        (d) Dynamically created VLAN, (D) VLAN Admin Disabled,
        (e) CES Configured, (E) ESRP Enabled, (f) IP Forwarding Enabled,
        (F) Learning Disabled, (h) TRILL Enabled, (i) ISIS Enabled,
        (I) Inter-Switch Connection VLAN for MLAG, (k) PTP Configured,
        (l) MPLS Enabled, (L) Loopback Enabled, (m) IPmc Forwarding Enabled,
        (M) Translation Member VLAN or Subscriber VLAN, (n) IP Multinetting Enabled,
        (N) Network Login VLAN, (o) OSPF Enabled, (O) Flooding Disabled,
        (p) PIM Enabled, (P) EAPS protected VLAN, (r) RIP Enabled,
        (R) Sub-VLAN IP Range Configured, (s) Sub-VLAN, (S) Super-VLAN,
        (t) Translation VLAN or Network VLAN, (T) Member of STP Domain,
        (v) VRRP Enabled, (V) VPLS Enabled, (W) VPWS Enabled, (Z) OpenFlow Enabled

Total number of VLAN(s) : 8
* X4.89 # sh vlan x1h1
VLAN Interface with name x1h1 created by user
    Admin State:         Enabled     Tagging:   802.1Q Tag 101
    Description:         None
    Virtual router:      VR-Default
    IPv4 Forwarding:     Disabled
    IPv4 MC Forwarding:  Disabled
    IPv6 Forwarding:     Disabled
    IPv6 MC Forwarding:  Disabled
    IPv6:                None
    STPD:                s1(Disabled)
    Protocol:            Match all unfiltered protocols
    Loopback:            Disabled
    NetLogin:            Disabled
    OpenFlow:            Disabled
    TRILL:               Disabled
    QosProfile:          None configured
    Egress Rate Limit Designated Port: None configured
    Flood Rate Limit QosProfile:       None configured
    Ports:   7.           (Number of active ports=7)
       Tag:        *1,     *2,     *3,     *4,     *5,     *6,     *7
        Flags:    (*) Active, (!) Disabled, (g) Load Sharing port
                  (b) Port blocked on the vlan, (m) Mac-Based port
                  (a) Egress traffic allowed for NetLogin
                  (u) Egress traffic unallowed for NetLogin
                  (t) Translate VLAN tag for Private-VLAN
                  (s) Private-VLAN System Port, (L) Loopback port
                  (x) VMAN Tag Translated port
                  (G) Multi-switch LAG Group port
                  (H) Dynamically added by MVRP
                  (D) TRILL Designated, (A) TRILL Appointed Forwarder
                  (I) Dynamically added by IDM
                  (U) Dynamically added uplink port
                  (V) Dynamically added by VM Tracking
Photo of L Messi

L Messi

  • 70 Points

Posted 4 years ago

  • 0
  • 1
Photo of PARTHIBAN CHINNAYA

PARTHIBAN CHINNAYA, Alum

  • 4,362 Points 4k badge 2x thumb
This is an example RSTP configuration for 3 vlans 
create stpd stpd1
configure stpd stpd1 mode dot1w
configure stpd stpd1 add vlan sales ports all
configure stpd stpd1 add vlan personnel ports all
configure stpd stpd1 add vlan marketing ports all
configure stpd stpd1 ports link-type point-to-point 1:1,2:1
configure stpd stpd1 tag 100-----------------------------------you are missing this carrir vlan command
enable stpd stpd1


Please correct your configuration
create stpd s1
configure stpd s1 mode dot1w
configure stpd s1 default-encapsulation dot1d
configure stpd s1 add vlan x1h1 ports 1 dot1d
configure stpd s1 add vlan x1h1 ports 2 dot1d
configure stpd s1 add vlan x1h1 ports 3 dot1d
configure stpd s1 add vlan x1h1 ports 4 dot1d
configure stpd s1 add vlan x1h1 ports 5 dot1d
configure stpd s1 add vlan x1h1 ports 6 dot1d
configure stpd s1 add vlan x1h1 ports 7 dot1d
Photo of PARTHIBAN CHINNAYA

PARTHIBAN CHINNAYA, Alum

  • 4,362 Points 4k badge 2x thumb
Hello Messi ,
Your issue fixed after changing configuration