Help My Hp switch has this command configured (stp edged-port enable) does any one know the syntax to do the same on summitx460 switch ?

  • 0
  • 1
  • Question
  • Updated 4 years ago
Hi all on my Hp switch i have this c ommand enabled stp edged-port enable does any one know the command or the syntax to do the same on summitx460 switch ?
Photo of shakil khan

shakil khan

  • 280 Points 250 badge 2x thumb

Posted 4 years ago

  • 0
  • 1
Photo of PARTHIBAN CHINNAYA

PARTHIBAN CHINNAYA, Alum

  • 4,362 Points 4k badge 2x thumb
configure stpd ports edge-safeguard enable
Photo of PARTHIBAN CHINNAYA

PARTHIBAN CHINNAYA, Alum

  • 4,362 Points 4k badge 2x thumb
Concepts guide 15.6 page 1051 for more information

This command applies only to ports that have already been configured as edge ports.Loop prevention and detection on an edge port configured for RSTP or MSTP is called edge safeguard.
An edge port configured with edge safeguard immediately enters the forwarding state and transmits
BPDUs.
If you disable this feature, the edge port enters the forwarding state but no longer transmits BPDUs
unless a BPDU is received by that edge port. This is the default behavior.
Recovery time starts as soon as the port becomes disabled. If no recovery-timeout is specified, the port
is permanently disabled.
BPDU restrict can be disabled using the configure stpd stpd_name ports bpdu-restrict
disableport_list command.
If edge safeguard is disabled, BPDU restrict is also disabled
Photo of shakil khan

shakil khan

  • 280 Points 250 badge 2x thumb
would i need to create stpd process then execute the command you have shown above?
Photo of PARTHIBAN CHINNAYA

PARTHIBAN CHINNAYA, Alum

  • 4,362 Points 4k badge 2x thumb
yes please
Photo of shakil khan

shakil khan

  • 280 Points 250 badge 2x thumb
command i have used as follow please correct me

create stpd sk12
configure stpd sk12 mode dot1w
configure stpd sk12 default-encapsulation dotd
enable stpd sk12 auto-bind vlan data
configure stpd sk12 ports link-type edge 2 edge-safeguard enable
enable stpd sk12
Photo of PARTHIBAN CHINNAYA

PARTHIBAN CHINNAYA, Alum

  • 4,362 Points 4k badge 2x thumb
Add the vlans and ports to stp
Photo of shakil khan

shakil khan

  • 280 Points 250 badge 2x thumb
have i not done that here

enable stpd sk12 auto-bind vlan data
configure stpd sk12 ports link-type edge 2 edge-safeguard enable
Photo of PARTHIBAN CHINNAYA

PARTHIBAN CHINNAYA, Alum

  • 4,362 Points 4k badge 2x thumb
if you are using only default vlan then its ok
Photo of shakil khan

shakil khan

  • 280 Points 250 badge 2x thumb
i have all port in vlan "data" and the above command should enable edge safeguard for all the port in the data vlan ?
Photo of PARTHIBAN CHINNAYA

PARTHIBAN CHINNAYA, Alum

  • 4,362 Points 4k badge 2x thumb
configure stpd stpd_name add vlan vlan_name ports
Photo of shakil khan

shakil khan

  • 280 Points 250 badge 2x thumb
i think the correct synax is

create stpd sk12
configure stpd sk12 mode dot1w
configure stpd sk12 default-encapsulation dotd
enable stpd sk12 auto-bind vlan data>>>>replace with configure stpd sk12 add vlan data ports all
configure stpd sk12 ports link-type edge 2 edge-safeguard enable
enable stpd sk12

enable stpd sk12 auto-bind vlan data 
&
configure stpd sk12 add vlan data ports all

both above command do same thing
Photo of PARTHIBAN CHINNAYA

PARTHIBAN CHINNAYA, Alum

  • 4,362 Points 4k badge 2x thumb
If you have only one vlan then it's ok
Photo of shakil khan

shakil khan

  • 280 Points 250 badge 2x thumb
also the above command are used if you have rstp LOL they are slightly different with MSTP
Photo of shakil khan

shakil khan

  • 280 Points 250 badge 2x thumb
do you know the syntax for the below for xos

how i can set broadcast-supression to 3000?
broadcast-suppression pps 3000: This command is used to suppress broadcast frames/packets, if the interface receives more than 3000 broaddcast packets per second, the interface will drop them. XOS supports this functionality, you will need to look in the config guides to determine how it’s done.

 


Photo of PARTHIBAN CHINNAYA

PARTHIBAN CHINNAYA, Alum

  • 4,362 Points 4k badge 2x thumb
Here it is
configure ports port_list rate-limit flood [broadcast | multicast | unknowndestmac][no-limit | pps]
Different question could you please mind opening a new query in future.
Photo of shakil khan

shakil khan

  • 280 Points 250 badge 2x thumb
hi - i can see this 
configure port 1-3 rate-limit and not anything else i cannot see the broadcast option