Hoe to determine which SFP GBIC is installed in a X650?

  • 0
  • 1
  • Question
  • Updated 4 years ago
  • (Edited)
I'm trying to determine what model of GBIC is installed into one of the SFP port in X650 switch? I read somewhere that you can view this info via the HAL.
Photo of Matt Tinonga

Matt Tinonga

  • 372 Points 250 badge 2x thumb

Posted 4 years ago

  • 0
  • 1
Photo of Marcus Ladarp

Marcus Ladarp

  • 100 Points 100 badge 2x thumb

debug hal show optic-info slot 1  (if switch is stacked)

If port is in Another slot you ,ust Telnet into the actual slot and run the command.

You will get info of all ports.

Photo of Jason Parker

Jason Parker, Employee

  • 3,038 Points 3k badge 2x thumb
* X150-24p.4 # debug hal show optic port 25
Port                       25
SFP or SFP+:               SFP
Signal:                    present
TX Fault:                  no
SFP/SFP+ Vendor:           Molex Inc.     
SFP/SFP+ Part Number:      74741-0001     
SFP/SFP+ Serial Number:    52001807       
SFP/SFP+ Manufacture Date: 050720
SFP/SFP+ Type:             SFP
Connector:                 Unknown
GE Compliance:             1000BASE-T
Wavelength:                0
Photo of MrGuga

MrGuga

  • 294 Points 250 badge 2x thumb
show ports 5:1 transceiver information detail
Port :  5:1
    Media Type            : XFP_SR
    Part Number           : TRF2001EN-GA170
    Serial Number         : 1104A-xxxxx

    Temp (Celsius)        : 28.70
          Low Warn Threshold  : -5.00       High Warn Threshold  : 85.00
          Low Alarm Threshold : -10.00      High Alarm Threshold : 90.00
          Status : Normal

    Tx Power (dBm)        : -2.23
          Low Warn Threshold  : -7.30       High Warn Threshold  : -1.30
          Low Alarm Threshold : -7.80       High Alarm Threshold : -0.80
          Status : Normal

    Rx Power (dBm)        : -2.58
          Low Warn Threshold  : -9.90       High Warn Threshold  : -1.00
          Low Alarm Threshold : -10.40      High Alarm Threshold : -0.50
          Status : Normal

    Tx Bias Current (mA)  : 5.48
          Low Warn Threshold  : 3.00        High Warn Threshold  : 12.00
          Low Alarm Threshold : 2.00        High Alarm Threshold : 13.00
          Status : Normal

    Voltage AUX-1/Vcc (Volts) : 3.33
          Low Warn Threshold  : 3.13        High Warn Threshold  : 3.46
          Low Alarm Threshold : 3.07        High Alarm Threshold : 3.53
          Status : Normal

    Voltage AUX-2 (Volts) : N/A
          Low Warn Threshold  : N/A         High Warn Threshold  : N/A
          Low Alarm Threshold : N/A         High Alarm Threshold : N/A
          Status : N/A
Photo of Jason Parker

Jason Parker, Employee

  • 3,038 Points 3k badge 2x thumb
Note:
This needs to be a  1000T transceiver  or DDMI is not supported
Photo of Matt Tinonga

Matt Tinonga

  • 372 Points 250 badge 2x thumb

# debug hal show optic-info slot 1

This worked gave the info I needed, Thanks.