How do upgrade SFP 1gb link to 10 gig onx440

  • 0
  • 1
  • Question
  • Updated 6 months ago
  • Answered
How do upgrade SFP 1gb link to 10 gig on x440 switch?
Photo of Alok Shukla

Alok Shukla

  • 944 Points 500 badge 2x thumb

Posted 8 months ago

  • 0
  • 1
Photo of Ronald Dvorak

Ronald Dvorak, Embassador

  • 46,958 Points 20k badge 2x thumb
Could you please provide the exact model of the switch.
Photo of Alok Shukla

Alok Shukla

  • 944 Points 500 badge 2x thumb
X440-G2-24t-10GE4
Photo of Alok Shukla

Alok Shukla

  • 944 Points 500 badge 2x thumb
I want know proper command by which we upograde link
Photo of Lutha

Lutha

  • 304 Points 250 badge 2x thumb
Ho Alok

you will need a licence to activate the 10g speeds i cnt remember exactly which licence i think its edge but m not sure someone can better point which licence to use for 10 g speeds and any other additional features you may want 
Photo of Alok Shukla

Alok Shukla

  • 944 Points 500 badge 2x thumb
i want upgradation of link 1gig to 10gig.
Photo of Lutha

Lutha

  • 184 Points 100 badge 2x thumb
You require the 10gb port licence to upgrade like Ronald says please look at the data sheet it will point you in the right direction
Photo of Ronald Dvorak

Ronald Dvorak, Embassador

  • 46,958 Points 20k badge 2x thumb
You need the license.

If you take a look into the datasheet...
https://cloud.kapostcontent.net/pub/b9e7ae6c-3734-463e-bb6e-b1d067c59623/extremeswitching-x440-g2-ds...
...on page#11 you have this two...


16542 Dual 10GbE Upgrade License License that converts the two non-stack 1GbE SFP ports to be 10GbE SFP+

16543 Quad 10GbE Upgrade License License that converts four 1GbE SFP ports to be 10GbE SFP+

That would allow either 2x or 4x 10GB ports.

Then you 'd need to plug in the 10GB SFPs and it should work.
Photo of Karthik Mohandoss

Karthik Mohandoss, Employee

  • 5,868 Points 5k badge 2x thumb
Photo of Robert Zdzieblo

Robert Zdzieblo

  • 1,186 Points 1k badge 2x thumb
Hi Alok,

You need to redeem the upgrade license at Extreme's extranet to get the license key, then you have to issue the following command at the switch CLI:

# enable license <your_license_key_here>

Your X440-G2 switch should be ready to use 10Gig modules.


REGARDS  
Photo of vishal android

vishal android

  • 60 Points
I upraded licence with "
  • 16542 - Dual 10GbE Upgrade License - License that converts the two non-stack 1GbE SFP ports to be 10GbE SFP+" but port is not getting active. No led indication.
Photo of Grosjean, Stephane

Grosjean, Stephane, Employee

  • 12,784 Points 10k badge 2x thumb
This license upgrades the 2 non-stack port to 10G. Physically speaking, this is the first two. So only these ports can do 10G, out of the 4 available. Are you connecting to the correct ports?