cancel
Showing results forĀ 
Search instead forĀ 
Did you mean:Ā 

Problems with port Sharings X670

Problems with port Sharings X670

Julian_Eble
New Contributor II
Hello,

There's something odd happenings here, and more than that was the solution of it.

We've a sharing with a Juniper MX80, and there're two 10G ports connect on, the 47 and 48 (Extreme).
After issuing the command:

configure sharing 47 add ports 45,46

The hashings seens to not work properly.
The traffic droped significantly, the two added ports (45,46) seems to be more affected than the 47,48.

Then comes the odd "solution", after disabling the sharing and adding again with the master becoming port 45, the problem was solved.

It's a problem to be checked, because it's the second time that I'm having the same problem.
I'm using the version 15.6.3.1 v1563b1-patch1-5.
X670.
17 REPLIES 17

Patrick_Voss
Extreme Employee
Can you send the "show sharing" output and explain how you are determining the traffic is being affected?

I agree with that, but why when I do the same thing with other switchs this problem doesn't occur?
I mean, the thing is the master port number, if you add some ports that's not the sequential the same behavior appears.
I tested that with another switch and another MX, the MX had other firmware.
But I had the same symptoms

Based on this, it looks like what Jarek said is probably what happened. When the sharing was disabled on the X670, the LACP would drop causing the ports to be removed from the LAG on the MX80 as well.

When it came back up, the existing flows from the MX80 were re-hashed including the new ports.

-Brandon

Load Sharing Monitor
Config Current Agg Ld Share Ld Share Agg Link Link Up
Master Master Control Algorithm Group Mbr State Transitions
==============================================================================
8 8 LACP L3_L4 8 Y A 3
L3_L4 9 Y A 3
27 27 LACP L3_L4 27 Y A 1
L3_L4 28 Y A 1
29 29 LACP L3_L4 29 Y A 1
L3_L4 30 Y A 1
L3_L4 31 Y A 1
47 45 LACP L3_L4 45 Y A 1
L3_L4 46 - R 0
L3_L4 47 Y A 2
L3_L4 48 Y A 2
==============================================================================

Below I enabled just one port to see if the problems happens.
After that the traffic became this:

Port Link Link Rx Peak Rx Tx Peak Tx State Speed % bandwidth % bandwidth % bandwidth % bandwidth
================================================================================
45 A 10000 1.59 2.96 0.99 1.09
46 R 0 0.00 0.00 0.00 0.00
47 A 10000 26.33 38.23 34.27 50.37
48 A 10000 24.27 40.51 43.32 63.29

Port 45 has a much less traffic then the others ports.
We have about 5 lacp on this switch with the Juniper, none had this kind of problem.

The only behaviour was about using predecessors ports of the master sharing port.
As I said before, after disabling/enabling the sharing and set the port 45 as Master the traffic became ok.

Here's the output now:

X670 # sh sharingLoad Sharing Monitor
Config Current Agg Ld Share Ld Share Agg Link Link Up
Master Master Control Algorithm Group Mbr State Transitions
==============================================================================
8 8 LACP L3_L4 8 Y A 4
L3_L4 9 Y A 3
27 27 LACP L3_L4 27 Y A 1
L3_L4 28 Y A 1
29 29 LACP L3_L4 29 Y A 1
L3_L4 30 Y A 1
L3_L4 31 Y A 1
45 45 LACP custom 45 Y A 2
custom 46 Y A 2
custom 47 Y A 2
custom 48 Y A 2
==============================================================================
Link State: A-Active, D-Disabled, R-Ready, NP-Port not present, L-Loopback
Load Sharing Algorithm: (L2) Layer 2 address based, (L3) Layer 3 address based
(L3_L4) Layer 3 address and Layer 4 port based
(custom) User-selected address-based configuration
Custom Algorithm Configuration: ipv4 L3-and-L4, crc-32 upper
Number of load sharing trunks: 4

X670 # sh ports 45-48 utilization bandwidth
Port Link Link Rx Peak Rx Tx Peak Tx
State Speed % bandwidth % bandwidth % bandwidth % bandwidth
================================================================================
45 A 10000 15.95 15.95 44.13 44.13
46 A 10000 15.75 15.75 38.12 38.12
47 A 10000 15.87 38.23 4.10 51.62
48 A 10000 15.99 40.51 5.93 63.29
================================================================================
> indicates Port Display Name truncated past 8 characters
Link State: A-Active, R-Ready, NP-Port Not Present, L-Loopback
GTM-P2G8KFN