trying to configure a simple network

  • 0
  • 1
  • Question
  • Updated 1 year ago
  • Answered
  • (Edited)
just purchased extreme network 440 and a new router. Its my understanding i don't need a router that the switch can do dhcp as well? if this is the case how would i set the static from my isp on a specific port and be able to utilize the rest of the ports for connection to other devices for connection to the internet. just one vlan so i can begin to learn these switches. trying to keep it simple for now. i've managed to set an ip on the switch and can access the gui. but i dont know how to set one of the ports to be my "in" port from my modem w static settings
Photo of Gus Rodriguez

Gus Rodriguez

  • 254 Points 250 badge 2x thumb

Posted 1 year ago

  • 0
  • 1
Photo of Ram

Ram, Employee

  • 1,450 Points 1k badge 2x thumb
Yes, x440 can used for DHCP. You can uplink the ISP connection on the x440 switch and assign that port to a vlan for connectivity.

How to create and delete static routes in EXOS:
https://gtacknowledge.extremenetworks.com/articles/How_To/How-to-create-and-delete-static-routes-in-...

How To Configure a default route in EXOS:
https://gtacknowledge.extremenetworks.com/articles/How_To/Configure-a-default-route-in-EXOS
Photo of Narayanan, Karthikeyan

Narayanan, Karthikeyan, Employee

  • 912 Points 500 badge 2x thumb
Hi Gus,

Before adding the route on our switch, please make sure NATing  is done. 
I assume it's been take care before it reaches x440.
EXOS platform devices will not support NAT feature.

Regards,
Karthikeyan
Photo of Narayanan, Karthikeyan

Narayanan, Karthikeyan, Employee

  • 912 Points 500 badge 2x thumb
(Edited)
Photo of Gus Rodriguez

Gus Rodriguez

  • 254 Points 250 badge 2x thumb
is it possible to do all these configurations from the gui?
Photo of Tripathy, Priya Ranjan

Tripathy, Priya Ranjan, ESE

  • 2,306 Points 2k badge 2x thumb
Unlike cisco SBCS and other platform there is no support for GUI on our extreme switches. Here you can always configure the required things either by CLI or chalet screenplay features.

Please find below link talking more about this screenplay feature:

https://gtacknowledge.extremenetworks.com/articles/Solution/After-upgrading-EXOS-GUI-is-Screenplay-s...
Photo of Narayanan, Karthikeyan

Narayanan, Karthikeyan, Employee

  • 912 Points 500 badge 2x thumb
Hi Gus,

As per your description, I believe you are able to access the GUI already. The most of the configuration can be done in GUI itself. 



Please let me know if you need any help in particular.

Regards,
Karthikeyan
Photo of Gus Rodriguez

Gus Rodriguez

  • 254 Points 250 badge 2x thumb
yes i am able to access the gui and and would like to use my own router. i have my isp configured in our router and need to connect it to the switch is the setup i believe we are going to go w. so from what i understand is i just need to untag the port that our router will be plugging into the extreme switch as all ports are on the default vlan as of now. is this correct? i have an ip set for the extreme switch set to 10.1.1.2 and dhcp on the router dhcp configured for 10.1.1.1-10.1.1.250
Photo of Ram

Ram, Employee

  • 1,450 Points 1k badge 2x thumb
It is not possible to connect the Extreme switch directly with ISP IP gateway. Since the Summit switches don't support NAT. I would recommend adding a firewall or a device that supports NAT. Yes, by default all ports are mapped to default vlan.
Photo of Gus Rodriguez

Gus Rodriguez

  • 254 Points 250 badge 2x thumb
so if i have a router configured running dhcp  and have it plugged into the switch w just one vlan to start w/ what do i have to do to the port the router is connected to for dhcp from the router to give ips to the rest of the ports?
Photo of Vellachery, Sumeesh

Vellachery, Sumeesh, Employee

  • 3,268 Points 3k badge 2x thumb
Gus Rodriguez,

Let's assume we have got only the default vlan residing in the switch and your Router/DHCP is connected in the same vlan interface.
In this case, the clients connected to the default vlan will be getting the ip-address from the DHCP server. Since, the clients and the DHCP server are in the same vlan.  

In case, if there are multiple vlans created on the switch. And also, your DHCP server is residing on a different subnet/connected to a different vlan interface of the switch.
Then we would need to configure the bootprelay on those vlans for the clients to receive ip-adress from the DHCP server. 
Photo of Gus Rodriguez

Gus Rodriguez

  • 254 Points 250 badge 2x thumb
Ok I'm understanding I little better now. I'm going to give it a shot tomorrow. If I need further assistance is there some one I can speak to or do I just have to post here in the forums?
Photo of Vellachery, Sumeesh

Vellachery, Sumeesh, Employee

  • 3,268 Points 3k badge 2x thumb
Gus Rodriguez,

GTAC is 24/7. You could reach us at any time. Also, you could post here in the forum.