cancel
Showing results for 
Search instead for 
Did you mean: 

Urgent ,Getting a wrong DSCP value ,Vary urgent

Urgent ,Getting a wrong DSCP value ,Vary urgent

Zool_Zool
New Contributor
I am trying to config ExtremeXOS version 16.1.3.6 16.1.3.6-patch1-8 to bypass DSCP values without Doing Any marking or replacement ,but i am getting DSCP value of 0 in the next node ,

below is my configuration:

QoS Profile: None configured
Ingress Rate Shaping : Unsupported
Ingress IPTOS Examination: Disabled
Ingress 802.1p Examination: Enabled
Ingress 802.1p Inner Exam: Disabled
Ingress 802.1p Priority: 0 <======
Egress IPTOS Replacement: Disabled
Egress 802.1p Replacement: Disabled

all traffic is passing through QP1

Qos Monitor Req Summary Wed Nov 9 13:14:54 2016 Port QP1 QP2 QP3 QP4 QP5 QP6 QP7 QP8
Pkt Pkt Pkt Pkt Pkt Pkt Pkt Pkt
Xmts Xmts Xmts Xmts Xmts Xmts Xmts Xmts
===============================================================================
13 45947598 0 0 0 0 0 0 1928

CodePoint->QOSProfile mapping:

00->QP1 01->QP1 02->QP1 03->QP1 04->QP1 05->QP1 06->QP1 07->QP1

08*>QP1 09*>QP1 10*>QP1 11*>QP1 12*>QP1 13*>QP1 14*>QP1 15*>QP1

16*>QP1 17*>QP1 18*>QP1 19*>QP1 20*>QP1 21*>QP1 22*>QP1 23*>QP1

24*>QP1 25*>QP1 26*>QP1 27*>QP1 28*>QP1 29*>QP1 30*>QP1 31*>QP1

32*>QP1 33*>QP1 34*>QP1 35*>QP1 36*>QP1 37*>QP1 38*>QP1 39*>QP1

40*>QP1 41*>QP1 42*>QP1 43*>QP1 44*>QP1 45*>QP1 46*>QP1 47*>QP1

48*>QP1 49*>QP1 50*>QP1 51*>QP1 52*>QP1 53*>QP1 54*>QP1 55*>QP1

56->QP8 57->QP8 58->QP8 59->QP8 60->QP8 61->QP8 62->QP8 63->QP8

what is wrong with my configuration ???

Do i need to Set different Ingress 802.1p Priority value ??
or Ingress 802.1p Examination ???


6 REPLIES 6

Zool_Zool
New Contributor
Dears,

Thanks for your quick response ,

Actually I am New In QOS concept , i am A telecom Engineer trying to forward the traffic from Access Node (BSC) to the Core Node (MSC) through extreme Switch .

------
[bsc](DCSP 46)=====>[extreme Switch]===========> [msc]

I need to Bypass the traffic without marking or replacing the DSCP value ,but with the above mentioned Configuration on Port 13 the MSC received wrong DSCP value (0) .

CodeRed_Red
New Contributor
Hi

Drew_C
Valued Contributor III
Hi Zool, Welcome to The Hub!
Keep in mind that if you urgently need assistance, your best bet is to contact GTAC. Looks like Bill and Henrique jumped on this pretty quickly though 🙂
See: How to contact Extreme Networks Global Technical Assistance Center (GTAC)

Henrique
Extreme Employee
Hi Zool, both DSCP and 802.1p are used for QOS priority, but they work in a different way.

In a simple description, DSCP is for L3 traffic (IP packet) and 802.1p is L2 traffic (3 bits used from a vlan tagged frame).

The first question here would be: What priority mechanisms are you willing to use? DSCP or 802.1p?

If you are working with DSCP, you have to enable DSCP examination and also change the default DSCP mapping as already described by Bill.
GTM-P2G8KFN